Controlled Products Systems Group 9000-080 - Manual (Page 41)

9000-065-F-9-10 39
7.4 Accessory Items
The following accessory items are available for the model 9000 slide gate operator.
Contact Sensors - For use as a secondary entrapment protection device. Miller Edge, Inc., MGO20, MGR20, MGS20
Photo Cell - Non-contact (photocell) sensors for use as a secondary entrapment protection device.
MMTC, Inc. Model IR55 - P/N 8080-010 MMTC, Inc. Model 60-278 - P/N 8080-011
Carlo Gavazzi Type PMP12 - P/N 8080-030 Carlo Gavazzi Type PMT - P/N 8080-031
Loop Detector - Detectors plug directly into ports on circuit board simplifying wiring.
Single channel detector - P/N 9410-010 Dual channel detector - P/N 9409-010
Loop Wire - 18 AWG loop wire with XLPE insulation is ideal for ground loops. Available in 500 and 1000 foot rolls. Red, blue or
black insulation.
Pre-Fab Loops - Prefabricated ground loops. 24-foot circumference with 50-foot lead-in. Available in yellow, red or blue jackets.
Not for use in asphalt roadways.
Loop Test Meter - Meg-ohm meter checks the integrity of ground loops. P/N 9401-045
Remote Alarm/Reset Station - Provides a remote station to reset an operator in a hard shutdown condition. Must be mounted
in line-of-site of the gate and operator. Includes visual alarm light and audible siren. P/N 1404-080.
Interconnection Cable - Interconnect wire cable contains all the necessary wires to interconnect primary / secondary operators.
Cable length: 30 ft. - P/N 2600-755 40 ft. - P/N 2600-756 50 ft. - P/N 2600-757
Time Clock - 7 day and 365 day time clocks can be used to automatically open gate at pre-set time and days. Compact clock fits
inside the operator. 7 day clock - P/N 2600-791 365 day clock - P/N 2600-795
Heater with Fan Assembly Kit - Thermostatically controlled heater and fan for cold and hot environments. P/N 1601-154
V-Wheels - 4 inch and 6 inch. UHMW or Steel. Roller bearings or sleeve bearings. Single or tandem wheel configurations.
Endless Idler Assembly with Protective Cover - Use when gate operator chain needs 180° return. P/N 2600-818
Guide Rollers with Protective Covers - A variety of sizes to support slide gates.
Gate End Retainer - Fits on top of end post and helps stabilize the end of the gate in the open or closed position (End post NOT
provided). P/N 1204-004
Post Mount Kit for 9000 - Required for post mount installation. P/N 9000-015.
Chain Tray Kit - 10 Ft. section. Sections connect together to fit any length gate. P/N 2601-270
Additional #40 Chain - 20 ft. per box. P/N 2600-442
Surge Devices - High and low voltage surge suppressors help prevent circuit board failure caused by lightning strikes and
power surges. High Voltage - P/N 1876-010 Low Voltage - P/N 1878-010
Gate Scale - Use to test torque required to move gate. P/N 2600-225
Speed Bumps - Prefabricated six-foot speed bump reduces traffic speed through gate system. P/N 1610-150
1000 Inverter/Back-Up Power System - Power back-up and continuous operation when 115 VAC primary (AC) power has
failed. 1000 Watt Model (P/N 1000-080) can be used to power a single 1/2 HP gate operator system when operating continu-
ously or used with two (2) 1/2 HP gate operator system when opening ONLY ONCE upon a power failure. The “Two battery
option” extends the number of times the system can cycle with battery power but does not increase the HP or number of
operators that can be used. 1500 Watt Model (P/N 1000-081) can be used to power two (2) 1/2 HP gate operator system or a
single 1 HP gate operator system when operating continuously. Not available for the 208/230 or 460 model 9000 operators.
Mounting post kit for 1000 inverter cabinet
(P/N 1000-045)
Conc
rete
Power Input
Low
Vo
ltage
to Ope
rator
Low
Vo
ltage
to
seco
nd
ary
op
era
tor
if
requir
ed.
Low
V oltage
AC Powe
r to
Ope
rat or
AC p
ow
er
to s
eco
nda
ry
ope
rat
or if
requ
ired.
Pow
er
Outp
ut
Input A
C Power
W AR NING
M OV ING GA TE C AN CA US E
Per son s ar e to keep cle ar! Th e g ate is c apa ble of
bein g m ove d w ith out prio r w arn ing .
Do no t le t ch ildr en o per ate th e g ate or p lay in th e
gat e ar ea . This en tran ce is for veh icle s o nly . Pe des tria ns
mu st u se a se par ate entr anc e.
Per son s ar e to rea d th e o wn er’s m anu al a nd
safe ty in stru ctio ns. For ga te o per ato r usi ng T ype D e ntr apm ent
pro tec tion , an au tom atic clo sin g d evi ce ( suc h a s a
tim er, l oop se nso r or sim ilar devi ce) sh all n ot b e
em plo yed .
SE RIO US IN JU RY OR DE AT H CLA SS
CER TIF IED TO CA N/C SA C2 2.2 NO . 2 47
CO NF OR MS TO AN SI/U L-3 25 VEH ICU LA R G ATE OP ER AT OR HP
533 82 MO DE L SER IAL VO LTS PH AS E AM PS 60 H z MA X G ATE LO AD Doo rK ing , In c., I ngle wo od, CA
Inver
ter
Cabinet
on
Mounting
Post
9000
Sample Installation
Individual installations will vary.