Document Outline

• HP 3 Phase UPS User Guide
• Abstract
• Notice
• Contents
• Component identification
  • 3 Phase UPS overview
  • UPS front panel
  • UPS front panel controls
  • UPS front panel LED indicators
  • UPS rear panel
    • REPO port
  • ERM rear panel
• UPS installation
  • Precautions
  • Preparing to install the hardware
    • Tools and materials
    • Selecting a site
    • Readying the equipment
  • Installing the mounting rails
  • Installing the UPS
    • Removing the UPS battery bracket
    • Installing the batteries
    • Replacing the UPS battery bracket
    • Attaching the UPS front bezel
    • Connecting the ground bonding cable
    • Connecting the REPO port
      • Connecting to a normally-open contact
      • Connecting to a normally-closed contact
    • Connecting the UPS to utility power
    • Switching on the UPS battery circuit breaker
    • Connecting devices to the UPS
    • Charging the UPS batteries
    • Powering up the standalone UPS
  • Installing in a parallel configuration
    • Installing the input and output wiring
      • Bottom entry
      • Top entry
    • Wiring the terminal block
    • Connecting the ground bonding cable
    • Connecting the REPO port
      • Connecting to a normally-open contact
      • Connecting to a normally-closed contact
    • Connecting the UPSs to the Bus Bar
    • Switching on the UPS input circuit breaker
    • Switching on the UPS battery circuit breaker
    • Connecting devices to the UPS
    • Charging the UPS batteries
    • Powering up the parallel system
  • Adding an HP 3 Phase UPS to a parallel configuration
    • Disconnecting from utility power
    • Installing the UPS
      • Configuring the Parallel UPS Card
      • Removing the UPS battery bracket
      • Installing the batteries
      • Replacing the UPS battery bracket
      • Attaching the UPS front bezel
      • Connecting the ground bonding cable
      • Connecting the REPO port
        • Connecting to a normally-open contact
        • Connecting to a normally-closed contact
      • Connecting the UPSs to the Bus Bar
      • Connecting the UPS to utility power
      • Switching on the UPS input circuit breaker
      • Switching on the UPS battery circuit breaker
      • Connecting devices to the UPS
      • Charging the UPS batteries
      • Powering up the parallel system
• ERM installation
  • Preparing to install the hardware
    • Tools and materials
    • Selecting a site
    • Readying the equipment
  • Installing the mounting rails
  • Preparing the rails for integrated shipping
  • Switching off the UPS battery circuit breaker
  • Switching off the ERM circuit breaker
  • Installing the ERM
    • Attaching the ERM front bezel
    • Connecting the ERM to the UPS
    • Switching on the ERM circuit breaker
    • Switching on the UPS battery circuit breaker
    • Charging the ERM batteries
• UPS operations
  • Mimic screen
  • Modes of operation
    • Standby mode
    • Normal mode
      • Standard mode
      • Full-Time Standard mode
      • High Efficiency mode
      • Continuous double-conversion mode
      • Transferring the UPS between Normal modes
    • Battery mode
    • Auto-Bypass mode
      • Transferring the UPS between modes
  • Configuring the UPS
    • Changing the language
    • Changing display functions
      • Menu map for display functions
    • Changing user settings
  • Setting the Battery Low alarm level
  • Running automatic battery tests
  • Testing the front panel display
  • Silencing an audible alarm
  • Verifying the REPO port connection
  • Powering down the standalone UPS
  • Powering down an individual paralleled UPS
  • Powering down the parallel system
• Communication
  • Installing communication options and control terminals
  • Communication options
    • DB-9 communication port
      • Serial communications port pin assignment
  • Control terminals
  • Relay output contacts
  • Programmable signal inputs
  • Parallel communication
    • Mode transfers
    • Redundant signal wiring
    • Auto-identification
    • Metering
• Power management
  • HP UPS Power Protection Agent overview
  • Features
• Maintenance
  • Removing the UPS front bezel
  • Removing the ERM front bezel
  • Replacing the UPS electronics module
  • Replacing UPS X-Slot cards
  • Configuring the Parallel UPS Card
  • Replacing the batteries
    • Important battery safety information
    • Battery care and storage guidelines
    • UPS battery replacement procedure
    • Testing the new battery module
  • Replacing the UPS
  • Replacing the ERM
  • Updating the UPS firmware
    • Verifying the HP UPS Management Module firmware version
    • Configuring a USB to serial converter
    • Reassigning the USB COM ports
• Troubleshooting
  • LED and audible alarm troubleshooting
    • Silencing an audible alarm
  • Abnormal output voltage at startup
  • Battery breaker
  • Battery connection condition
  • Battery low condition
  • Battery test condition
  • Bypass is unavailable
  • Check Parallel Board condition
  • Configuration error and UPS does not start
  • Phase rotation verification
  • Power is not available at the UPS output receptacle
  • Protected equipment is not on
  • Overload condition
  • Overtemperature condition
  • Redundancy loss due to overload
  • Selective trip
  • Site wiring condition
  • UPS detects software incompatibility
  • UPS does not power down
  • UPS does not power up
  • UPS does not provide the expected backup time
  • UPS does not transfer to Auto-Bypass mode
  • UPS is on battery
  • UPS is on bypass
• Specifications
  • Model list
  • UPS physical specifications
  • ERM physical specifications
  • Power cord specifications
  • Power Bus Bar and Wireway specifications
  • HP 10642 G2 Rack specifications
  • UPS input specifications
  • UPS output specifications
  • Environmental specifications
  • Battery specifications
  • Battery runtimes
  • REPO port specifications
• Spares
  • Ordering spares
  • UPS spare parts list
  • Hardware options
• Support and other resources
  • Before you contact HP
  • HP contact information
• Regulatory information
  • Safety and regulatory compliance
  • Turkey RoHS material content declaration
  • Ukraine RoHS material content declaration
  • Warranty information
    • Limited warranty
    • $250,000 Computer Load Protection Guarantee
    • Pre-Failure Battery Warranty
• Electrostatic discharge
  • Preventing electrostatic discharge
  • Grounding methods to prevent electrostatic discharge
• Acronyms and abbreviations
• Documentation feedback
• Index