Table of figures – Weidmuller WI-I/O-9-U2: Wireless Mesh I/O & Gateway User Manual V1.2.2 User Manual
Page 11
10
TABLE OF FIGURES
– Power Connectors ......................... 16
– Supply Connections ....................... 16
– Expansion I/O power & RS485 ...... 18
Figure 5 - Earthing .......................................... 20
Figure 6 - Wrapping Coax Connections .......... 23
– Collinear Antenna mounting .......... 24
Figure 8 - Yagi Antenna Mounting .................. 25
– Bottom Panel Connections ............ 26
– RS485 Connections ..................... 27
– Side Access Panel ....................... 27
– Front Panel Connections ............. 29
– Digital / Pulsed Input Wiring ......... 30
– Digital Output Wiring .................... 31
– Digital Output Failsafe Times ....... 32
Figure 16 - Fail-Safe State .............................. 32
Figure 17
– Differential Current Inputs ............. 33
Figure 18
– Single Ended Current Inputs ........ 33
– Single Ended Current Inputs ........ 34
– Voltage Inputs .............................. 35
– Analog Outputs ............................ 36
Figure 22 - Boot Sequence ............................. 38
– Network Settings .......................... 46
Figure 24 - Ping ............................................... 46
– Main Welcome Screen ................. 47
Figure 26 - IP Gateway Mode ......................... 48
Figure 27 - Default Gateway ........................... 48
Figure 28 -IP Address Range ......................... 48
Figure 29 - Routing Rule ................................. 49
Figure 30 -Over the air Configuration ............. 49
Figure 31 - Installation ..................................... 51
– Configuration Software ................ 51
Figure 33 - Configuration Screen .................... 52
Figure 34 - Project Information........................ 53
Figure 35 - Create Units .................................. 53
Figure 36 - Unit Details ................................... 54
Figure 37 - ID Address List ............................. 55
Figure 38 - Mappings ...................................... 55
Figure 39 - Gather/Scatter Mapping ............... 57
Figure 40 - Startup/Force . Error! Bookmark not
defined.
Figure 41 - Startup/Force Configuration ......... 60
Figure 42 - I/O configuration ........................... 61
Figure 43 - Digital Inputs ................................. 62
Figure 44 - Digital Output ................................ 62
Figure 45 - Pulsed Outputs ............................. 62
Figure 46 - Analog Inputs Table ..................... 63
Figure 47- Analog Input .................................. 63
Figure 48 - Analog Output .............................. 64
Figure 49 - Expansion I/O ............................... 66
Figure 50 - Failsafe Block Analog ................... 66
Figure 51 - Failsafe Block Digital .................... 66
Figure 52- Invalid Register State .................... 67
Figure 53 - Sensitivity Block ........................... 68
Figure 54 - Modbus TCP/RTU ........................ 69
Figure 55 - Expansion I/O ............................... 70
Figure 56 - Modbus Configuration .................. 71
Figure 57 - Modbus TCP Client Mapping ....... 73
Figure 58 - Modbus TCP Mapping table ......... 74
Figure 59 - Modbus RTU Example ................. 75
Figure 60 - Operating Mode Error................... 75
Figure 61 - Modbus Parameters ..................... 76
Figure 62 - Mesh Configuration ...................... 76
Figure 63 - Neighbour RSSI ........................... 78
Figure 64 - IP Routing ..................................... 79
– Radio Configuration Screen ........ 80
Figure 66 - Mesh Fixed Route#1 .................... 82
Figure 67 - Mesh Fixed Route - Gateway ....... 82
Figure 68 - Mesh Fixed Route - Rep Site #2 .. 83
Figure 69 - Trace Route .................................. 83
Figure 70 - Mesh Fixed Route#2 .................... 83
– Mesh Fixed Route#2 Routing Rules
........................................................... 84