Electronic control module (main pc board) – SARGENT MPower 4000 User Manual
Page 3
80-9369-0901-021 (12-02 )
3
14
13
12
11
10
9
8
7
6
5
4
3
2
1
1 2 3 4 5 6 7 8
5
678
90
1
23
4
5
678
90
1
23
4
5
678
90
1
23
4
5
678
90
1
23
4
NEU HOT GND
18VAC
GND +24V NO1 CO1 NC1 NO2 CO2 NC2
0/0
RES1
A
UX2
GND
INV
OUTV
GND
R
F
T
GND
A
UX2
GND
PDET
GND
A
UX1
DOOR OPERATOR
41-6700-0056 REV A MADE IN USA
OFF
ON
SW1
P/A
A/D
RES1
RES2
JP4
JP1
JP5
JP3
JP2
CL/AS DLY VEST DLY
EXSOL DLY
M. DLY
G
EM
G
H+
V
L
2
G
L1
MO
T
O
R/SOLENOID
SW5 Rotary
Switch/Timer
Pot
SW4 Rotary
Switch/Timer
Pot
SW2 Rotary
Switch/Timer
Pot
SW3 Rotary
Switch/Timer
Pot
SW1 Dip
Switches
JP4 Terminal
Strip
JP1 Terminal
Strip
Fuse F1
1.5 amp,
2AG
Slo-Blo
Relay
K2
Relay
K1
Relay
K4
Relay
K3
JP2 Terminal
Strip
JP3 Terminal
Strip
Electronic Control Module (Main PC Board)
JP1 Terminal Strip – Maximum wire size 14AWG. For signaling only, do not make power input connections.
TERMINAL
D E S C R I P T I O N
1
0/0
– This terminal has two possible functions that can be used together or separately.
1.
– Upon initiation of a closed signal from a fire/ smoke alarm
panel, door will open and remain open until signal is terminated. Use with any JP1 ground.
2.
– Time is set with dip switch SW1 – 2 A/D. (OFF = 30
second delay, ON = 60 second delay) Use with any JP1 ground.
Override Open
Smoke Ventilation Door or Blow Open Door
Alarm Delay (30 second or 60 second time period)
2
RES1
This is not an active contact.
3
AUX2
– This is one of two secondary initiating switch contacts (JP1 – 10 is the other.)
For most applications it is equivalent to AUX1 JP1 – 14. For Vestibule Function use, it is the contact for a switch
located within the vestibule. Use with any JP1 ground.
Auxiliary 2
4
GND
Ground
5
INV
In Vestibule – Used for Vestibule Function. This contact must be connected to the JP1 – 6 terminal from another
unit to receive an initiating signal. The signal is then programed to initiate the unit by setting the VEST DLY rotary
switch/timer pot of the receiving unit. Use this contact with any JP1 ground.
6
OUTV
– Used for Vestibule Function. This contact must be connecter to terminal JP1 – 5 of another unit to
send an initiating signal. Use with any JP1 ground.
Out Vestibule
7
GND
Ground
8
RFT
– With the unit’s 3 Position Slide Switch in the “ON” position, a signal will open the door and
maintain an indefinite hold open until a second signal releases the door from hold open. Use with any JP1 ground.
Maintain Hold Open
This feature recommended for Power Operator Function. If using with the Power Assist Function, consult factory.
9
GND
Ground
10
AUX2
– Same as JP1 – 3 / AUX2 above.
Auxiliary 2
11
GND
Ground
12
PDET
– Permits wiring of a presence detector to prevent a closed door from opening or a door that is
fully open from closing. Use with any JP1 ground.
Presence Detector
13
GND
Ground
14
AUX1
Auxiliary 1 – Primary initiating switch contact. Initiates door power cycle. Must be Normally Open Momentary Dry
Contact. For Vestibule Function, the switch at outside of vestibule is connected to this terminal. (Outside switch to
outside unit’s JP1 – 14. Inside switch to inside unit’s JP1 – 14). Use with any JP1 ground.