GAI-Tronics CommandPLUS Series Desktop Console Installation and Service Manual - Manual (Page 35)

CommandPLUS Series Desktop Console Installation and Service Manual Console Diagnostics
31 12/10
Keyboard Diagnostics
When 1 is selected from the Service Diagnostics Menu, you are prompted to enter 1 to execute the
keyboard test or 2 to execute the LED test. Keyboard diagnostics allows the testing of all buttons and
LEDs on the front panel of the CommandPLUS Series Desktop Console. These diagnostics are useful in
servicing the unit should a problem occur. Press the
M ODE key at any time to exit these diagnostics.
Keyboard Test
The keyboard test is performed by pressing each button on the console except the L OCK and M ODE keys.
When a button is firmly pressed, a corresponding key code appears on the display. Each button press on
the console results in a different key code. Refer to Table 10 to assist you in determining the proper key
code for each button. If a key code does not appear or is different from the keycode table, service of the
front panel is necessary. Contact GAI-Tronics Technical Support. N
OTE : Keyboard diagnostics can
also be tested by pressing LOCK + MODE button simultaneously during power up.
Table 10. Diagnostic Keycodes
Channel
Sel
Keycode
WC1
Keycode
WC2
Keycode
TX
Keycode
Volume
Up Code
Volume
Down Code
1 2F/10 2E/20 2D/30 2C/40 36/60 37/70
2 28/11 29/21 2A/31 2B/41 34/61 35/71
3 27/12 26/22 25/32 24/42 32/62 33/72
4 20/13 21/23 22/33 23/43 30/63 31/73
5 1F/14 1E/24 1D/34 1C/44 3E/64 3F/74
6 18/15 19/25 1A/35 1B/45 3C/65 3D/75
7 17/16 16/26 15/36 14/46 3A/66 3B/76
8 10/17
11/27 12/37 13/47 38/67 39/77
9 0F/18 0E/28 0D/38 0C/48 46/68 47/78
10 08/19 09/29 0A/39 0B/49 44/69 45/79
11 07/1A 06/2A 05/3A 04/4A 42/6A 43/7A
12 00/1B 01/2B 02/3B 03/4B 40/6B 41/7B
Option
Button
Keycode
Option
Button
Keycode
Option
Button
Keycode
Multiselect 1 71/2C Transmit 4C/58 1 5F/01
Multiselect 2 70/2D F1 4E/1C 2 (abc) 58/02
Phone Patch 73/2E F2 49/1D 3 (def) 67/03
Radio Patch 72/2F F3 4D/1E Tel Hold 60/0C
Page 57/3C F4 4A/1F 4 (ghi) 5E/04
Clear 50/3D * 5C/0A 5 (jkl) 59/05
Coded 4F/3F Multi PL 6A/4E Lock None
Clear 48/3E Intercom 6B/56 0 5B/00
Monitor 4B/57
LED Test
The LED test prompts you to press keys to light all or individual LEDs. Upon first entering this test, all
LEDs should be off. Pressing any key should cause all LEDs to turn on. Subsequent key presses should
light individual LEDs during this test. If console fails to operate in this manner, contact GAI-Tronics
Technical Support.