Teac MD-CD1MKIII - Manual (Page 52)

52
TASCAM MD-CD1MKIII
16 – Messages and Troubleshooting
Operation messages
ª
Message Details/response
Blank Disc A blank recordable MD disc has been
inserted.
Complete
Editing operation has been successfully
completed.
Dubbing
Wait The unit is being readied for dubbing.
TOC Reading The table of contents data is being
read.
UTOC
Writing The user table of contents data is
being written to the disc.
Now Editing
Editing operation is being performed.
Over Write Overwrite recording mode is on.
Warning messages
ª
Message Details/response
Key Locked The entire panel is locked. To release
the lock, press and hold the TIME and
DISPLAY buttons simultaneously.
CD Locked The deck is locked. To release the lock,
select
none
under
PANEL LOCK?
in the SYSTEM submenu of the CD
menu.
MD Locked
Eject
Locked
Error Messages
ª
Message Details/response
Disc Error!
The disc has malfunctioned. Please
replace with a new disc.
Disc Full! No recording time remaining on the
disc, so new recording is not possible.
Title Full! No more titles can be recorded.
D-IN UNLOCK! Digital signals are not correctly input.
This message appears if the selected
input source (coaxial or optical) does
not correspond to the connected
terminal or the connected device is
powered off. Select the input source
correctly, or turn on the connected
device.
Not
Execute!
Editing cannot be completed due to
MD system limitations.
Not Audio! There is no audio signal from DIGITAL
INPUT.
No Track! There are no recorded tracks.
PGM Empty! There is no program
PGM Full! No new programs can be created.
W_
Protected! Write-protected MD disc, so recording
or editing is not possible.
Pre Master! A playback-only MD disc has been
inserted.
TOC Error!
TOC data is not correct.
Can't Edit! Editing cannot be performed due
to MD system limitations or editing
condition limits.
Can't Rec! Recording cannot start because the
Group playback mode is on.
Can't Sel!
Menu selection cannot be performed
due to selection prohibitions.
Can't Undo! You can’t undo since no editing has
been done.
Rec Error! There was an error during recording.
Please re-record.
Drive Error! There is a problem in the drive.
Sync Rec
ON!
The Sync mode is on, so the recording
cannot be started manually.
Err Group! There is a problem in the data of the
created group.
No Group! No groups have been created.
No DIR! The directory where the file is has not
been registered.
Decode Err! The MP3 file cannot be played back.
IR Disable! All remote control operations are
disabled.
Format Err! The unit does not support the format
of the MP3 files on the disc.
Troubleshooting
ª
There is no power to the unit.
Please check that the power cord is properly plugged in.
Disc Error!
is displayed.
The disc may be dirty. Please replace the disc.
Playback is not possible.
This may be due to condensation. In this case, remove
the disc, turn the power on and wait a few hours, then try
again.
No sound is output.
Confirm the connections with the audio system. •
Check the volume level, and proper amplifier operation. •
Recording isn’t possible.
The MD disc is set to write protect. Slide the tab on the •
cartridge to the closed position and try again.
Confirm the connections with the audio system.
•
Adjust the recording level. •
The disc may be for playback only. Please replace it •
with a recordable MD disc.
Remaining recording time on the MD is insufficient.
•
Please delete unwanted tracks or replace the MD disc.
Confirm amplifier operation.
•
Noise or static can be heard.
Please re-position the unit away from strong sources of
magnetism such as a television.
The MD-CD1MKIII does not retain settings.
While settings are retained each time they are made, in
some cases they will not be retained when the power is
turned off too soon. To prevent this from happening, do
not turn off the power right after making a setting.