Verilink NCC 2020 (880-503284-001) Product Manual - Manual (Page 17)

Quick Set-Up
Verilink NCC 2020 User Manual 2-3
Figure 2-3 NCC 2020 Configuration Menu
The factory default values for the NCC 2020 are shown. The unit is
in CSU mode (DIU bus =
NONE NONE NONE NONE) and the network interface (shown at
top right) is set for ESF framing and AMI line coding format.
The DSX-1 Equipment interface, shown at top left, is set for SF (D4)
framing and AMI line code. For this quick set-up, the Equipment
interface is not being used, as it would be in CSU mode or Drop and
Insert mode. Because this example will use all 24 timeslots for data
on a DIU 2130 module, Mux mode is required.
1. Type “A” and press E NTER . The prompt for bus selection
appears: DSU Bus (1)NONE (2)A (3)B (4)C (5)B,D&I EQ (6)A,D&I DSU Bus (1)NONE (2)A (3)B (4)C (5)B,D&I EQ (6)A,D&I DSU Bus (1)NONE (2)A (3)B (4)C (5)B,D&I EQ (6)A,D&I DSU Bus (1)NONE (2)A (3)B (4)C (5)B,D&I EQ (6)A,D&I
NET > NET > NET > NET >. Select “2” to use Data Bus A. This means that the CSU
and the DIU 2130 will use Data Bus A in the shelf to pass data
back and forth. The CSU is now in Mux mode. The EQPT LED
changes from red to green.
2. Type “F” and press E NTER . The prompt for line format appears:
Line Format(eq,net) 1(AMI,AMI) 2(AMI,B8ZS) 3(B8ZS,AMI) Line Format(eq,net) 1(AMI,AMI) 2(AMI,B8ZS) 3(B8ZS,AMI) Line Format(eq,net) 1(AMI,AMI) 2(AMI,B8ZS) 3(B8ZS,AMI) Line Format(eq,net) 1(AMI,AMI) 2(AMI,B8ZS) 3(B8ZS,AMI)
4(B8ZS,B8ZS) > 4(B8ZS,B8ZS) > 4(B8ZS,B8ZS) > 4(B8ZS,B8ZS) >. Select “4” for B8ZS (since the Equipment side
interface is not used, selection 2 would also work).
3. The default value for the density enforcement selection is not
correct for a B8ZS T1. Use the “Z” command and select “1” to
change it to NONE. B8ZS was developed to eliminate the need
for density enforcement.
CSU CONFIGURATION -- FW Rev 1.4 HW Fab 0.8 Type NCC 2020 -- CSU CONFIGURATION -- FW Rev 1.4 HW Fab 0.8 Type NCC 2020 -- CSU CONFIGURATION -- FW Rev 1.4 HW Fab 0.8 Type NCC 2020 -- CSU CONFIGURATION -- FW Rev 1.4 HW Fab 0.8 Type NCC 2020 --
|-----------------------| |-----------------------| |-----------------------| |-----------------------|
-------<< eq <<-------| K) keep alive AIS |-------<< net <<-------
-------<< eq <<-------| K) keep alive AIS |-------<< net <<------- -------<< eq <<-------| K) keep alive AIS |-------<< net <<------- -------<< eq <<-------| K) keep alive AIS |-------<< net <<-------
W) framing SF | T) alm thld DEF | W) framing ESF
W) framing SF | T) alm thld DEF | W) framing ESF W) framing SF | T) alm thld DEF | W) framing ESF W) framing SF | T) alm thld DEF | W) framing ESF
F) format AMI | | F) format AMI
F) format AMI | | F) format AMI F) format AMI | | F) format AMI F) format AMI | | F) format AMI
J) jitt buf 40 BITS | | J) jitt buf 40 BITS
J) jitt buf 40 BITS | | J) jitt buf 40 BITS J) jitt buf 40 BITS | | J) jitt buf 40 BITS J) jitt buf 40 BITS | | J) jitt buf 40 BITS
R) eq crc REGEN | | R) net crc REGEN
R) eq crc REGEN | | R) net crc REGEN R) eq crc REGEN | | R) net crc REGEN R) eq crc REGEN | | R) net crc REGEN
Y) xcode yel TO NET | | Y) xcode yel OFF
Y) xcode yel TO NET | | Y) xcode yel OFF Y) xcode yel TO NET | | Y) xcode yel OFF Y) xcode yel TO NET | | Y) xcode yel OFF
M) distance 0-133 | | L) lbO 0 DB
M) distance 0-133 | | L) lbO 0 DB M) distance 0-133 | | L) lbO 0 DB M) distance 0-133 | | L) lbO 0 DB
------->> eq >>-------| I) idle code ONES |------->> net >>-------
------->> eq >>-------| I) idle code ONES |------->> net >>------- ------->> eq >>-------| I) idle code ONES |------->> net >>------- ------->> eq >>-------| I) idle code ONES |------->> net >>-------
|-----------------------| Z) density 12%+80z
|-----------------------| Z) density 12%+80z |-----------------------| Z) density 12%+80z |-----------------------| Z) density 12%+80z
X) exit menu C1-C5) canned config X) exit menu C1-C5) canned config X) exit menu C1-C5) canned config X) exit menu C1-C5) canned config
S) save csu config Q) restore csu config
S) save csu config Q) restore csu config S) save csu config Q) restore csu config S) save csu config Q) restore csu config
A) diu bus NONE B) diu clock THRU A) diu bus NONE B) diu clock THRU A) diu bus NONE B) diu clock THRU A) diu bus NONE B) diu clock THRU
P) prm OFF
P) prm OFF P) prm OFF P) prm OFF
[1,1] NEAR TAC 2010 > [1,1] NEAR TAC 2010 > [1,1] NEAR TAC 2010 > [1,1] NEAR TAC 2010 >