Verilink NCC 2020 (880-503284-001) Product Manual - Manual (Page 19)

Quick Set-Up
Verilink NCC 2020 User Manual 2-5
The error message, in this case, means that the DIU 2130 is new
and has never been assigned to any CSU module in any slot of any
shelf. Ignore this error message.
Then the DIU 2130 Configuration Menu is displayed.
Figure 2-4 DIU 2130 Configuration Menu
NOTE: For the remainder of this chapter you will not be instructed
to press E NTER each time. Generally, the E NTER key is used
after each command or value entry.
The CSU command is used to assign the DIU 2130 module to the
CSU with which it will be used. Since the NCC 2020 contains a TAC
2010 CSU module, it will be used for the CSU in this example. Type
“C”. At the prompt
enter shelf > enter shelf > enter shelf > enter shelf > type “1”, at the prompt enter slot > enter slot > enter slot > enter slot >
type “1” again. This selects the NCC 2020 in slot one of shelf one as
the CSU for this DIU 2130 module.
The Timing Source defaults to CSU, meaning that the DIU 2130 will
derive its transmit clock from the source selected in the CSU
configuration (recovered network clock in this example). This is
correct for this example.
In the middle of the display, a line across the screen lists all 24
timeslots. The DS0 (timeslot) selection prompt appears at the
beginning of the next line,
Dp Dp Dp Dp. The lowercase p is a variable,
--- DIU 2130 CONFIGURATION/DIAGNOSTIC MENU --- --- DIU 2130 CONFIGURATION/DIAGNOSTIC MENU --- --- DIU 2130 CONFIGURATION/DIAGNOSTIC MENU --- --- DIU 2130 CONFIGURATION/DIAGNOSTIC MENU ---
S) save config Q) restore config X) exit menu
S) save config Q) restore config X) exit menu S) save config Q) restore config X) exit menu S) save config Q) restore config X) exit menu
C) CSU [ 0,0 ] C) CSU [ 0,0 ] C) CSU [ 0,0 ] C) CSU [ 0,0 ]
T) timing source CSU
T) timing source CSU T) timing source CSU T) timing source CSU
chnl 01 02 03 04 05 06 07 08 09 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 chnl 01 02 03 04 05 06 07 08 09 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 chnl 01 02 03 04 05 06 07 08 09 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 chnl 01 02 03 04 05 06 07 08 09 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24
Dp)port .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. ..
Dp)port .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. Dp)port .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. Dp)port .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. ..
Lead Toggles DTR) DSR) RTS) CTS) DCD) Lead Toggles DTR) DSR) RTS) CTS) DCD) Lead Toggles DTR) DSR) RTS) CTS) DCD) Lead Toggles DTR) DSR) RTS) CTS) DCD)
Forced Ports -/- -/- -/- -/- -/-
Forced Ports -/- -/- -/- -/- -/- Forced Ports -/- -/- -/- -/- -/- Forced Ports -/- -/- -/- -/- -/-
Port 1 Port 2 Statistics Port 1 Port 2 Statistics Port 1 Port 2 Statistics Port 1 Port 2 Statistics
Mp) mode 56K 56K FW/HW Rev...1.6/0.8
Mp) mode 56K 56K FW/HW Rev...1.6/0.8 Mp) mode 56K 56K FW/HW Rev...1.6/0.8 Mp) mode 56K 56K FW/HW Rev...1.6/0.8
Sp) scram/hdlc inv N/N N/N Battery.....OK
Sp) scram/hdlc inv N/N N/N Battery.....OK Sp) scram/hdlc inv N/N N/N Battery.....OK Sp) scram/hdlc inv N/N N/N Battery.....OK
Kp) clocking ST ST DTE Intf....V.35/V.35
Kp) clocking ST ST DTE Intf....V.35/V.35 Kp) clocking ST ST DTE Intf....V.35/V.35 Kp) clocking ST ST DTE Intf....V.35/V.35
Gp) LOS lead NONE NONE Data bus....NONE
Gp) LOS lead NONE NONE Data bus....NONE Gp) LOS lead NONE NONE Data bus....NONE Gp) LOS lead NONE NONE Data bus....NONE
Ep) enable loop YES YES Tp) test and monitor BEC Ep) enable loop YES YES Tp) test and monitor BEC Ep) enable loop YES YES Tp) test and monitor BEC Ep) enable loop YES YES Tp) test and monitor BEC
Np) near loopback OFF OFF Pp) monitor leads and status
Np) near loopback OFF OFF Pp) monitor leads and status Np) near loopback OFF OFF Pp) monitor leads and status Np) near loopback OFF OFF Pp) monitor leads and status
Fp) far loopback OFF OFF A) enable alarm reporting...YES
Fp) far loopback OFF OFF A) enable alarm reporting...YES Fp) far loopback OFF OFF A) enable alarm reporting...YES Fp) far loopback OFF OFF A) enable alarm reporting...YES
[1,2] DIU 2130 > [1,2] DIU 2130 > [1,2] DIU 2130 > [1,2] DIU 2130 >