Document Outline

• Contact :
• In USA:
• Outside USA:
• SECTION 1. SAFETY PRECAUTIONS
  • 1.1 GENERAL
  • 1.2 PRE-OPERATION
    • Operator Training and Knowledge
    • Workplace Inspection
    • Machine Inspection
  • 1.3 OPERATION
    • General
    • Trip and Fall Hazards
    • Electrocution Hazards
    • Tipping Hazards
    • Crushing and Collision Hazards
  • 1.4 TOWING, LIFTING, AND HAULING
• SECTION 2. USER RESPONSIBILITIES, MACHINE PREPARATION AND INSPECTION
  • 2.1 PERSONNEL TRAINING
    • Operator Training
    • Training Supervision
    • Operator Responsibility
  • 2.2 PREPARATION, INSPECTION, AND MAINTENANCE
  • 2.3 PRE-START INSPECTION
  • 2.4 FUNCTION CHECK
  • 2.5 DAILY WALK-AROUND INSPECTION
• SECTION 3. MACHINE CONTROLS AND INDICATORS
  • 3.1 GENERAL
  • 3.2 CONTROLS AND INDICATORS
    • Ground Control Station
    • Battery Charger/Hour Meter Indicators
    • Platform Control Station
    • Platform Control and Indicator Panel
    • Drive/Lift/Steer Joystick Control
  • 3.3 DECAL INSTALLATION
• SECTION 4. MACHINE OPERATION
  • 4.1 DESCRIPTION
  • 4.2 OPERATING CHARACTERISTICS AND LIMITATIONS
    • General
    • Placards
  • 4.3 PLATFORM LOADING
  • 4.4 BATTERY CHARGING
    • Battery Charger Fault Codes
  • 4.5 AC INVERTER OPERATION (OPTION)
  • 4.6 OPERATION
    • Platform/Ground Select Switch
    • Emergency Stop Switch
  • 4.7 RAISING AND LOWERING PLATFORM
    • Raising Platform
    • Lowering Platform
  • 4.8 STEERING AND TRAVELING
    • Steering
    • Driving Forward and Reverse
  • 4.9 PARKING AND STOWING MACHINE
  • 4.10 TIE DOWN/LIFT LUGS
    • Tie Down
    • Lifting
  • 4.11 TOWING
    • Electric Brake Release
    • Mechanical Brake Release
• SECTION 5. EMERGENCY PROCEDURES
  • 5.1 GENERAL INFORMATION
  • 5.2 EMERGENCY OPERATION
    • Operator Unable to Control Machine
    • Platform Caught Overhead
  • 5.3 PLATFORM MANUAL DESCENT
  • 5.4 INCIDENT NOTIFICATION
• SECTION 6. GENERAL SPECIFICATIONS AND OPERATOR MAINTENANCE
  • 6.1 INTRODUCTION
    • Other Publications Available Specific to this Machine:
  • 6.1 OPERATING SPECIFICATIONS
    • Platform Capacities
    • Dimensional Data
    • Tires
    • Batteries
  • 6.1 CRITICAL STABILITY WEIGHTS
  • 6.1 LUBRICATION
    • Lubrication Capacities
    • Hydraulic Oil
    • Lubrication Specifications
  • 6.1 OPERATOR MAINTENANCE
    • Oil Check Procedure
  • 6.1 BATTERY MAINTENANCE
    • Battery Maintenance and Safety Practices
  • 6.1 TIRES AND WHEELS
    • Tire Wear and Damage
    • Wheel and Tire Replacement
    • Wheel Installation
  • 6.1 SUPPLEMENTAL INFORMATION
  • 6.1 DIAGNOSTIC TROUBLE CODES (DTC)
  • 6.1 DTC CHECK TABLE INDEX
  • 6.2 Diagnostic trouble codes (DTC) Check Tables
    • 0-0 Help Comments
    • 2-1 Power-Up
    • 2-2 Platform Controls
    • 2-3 Ground Controls
    • 2-5 Function Prevented
    • 3-1 Line Contactor Open Circuit
    • 3-2 Line Contactor Short Circuit
    • 3-3 Ground Output Driver
    • 4-2 Thermal Limit (SOA)
    • 4-4 Battery Supply
    • 6-6 Communication
    • 6-7 Accessory
    • 7-7 Electric Motor
    • 8-1 Tilt Sensor
    • 8-2 Platform Load Sense
    • 9-9 Hardware
• SECTION 7. INSPECTION AND REPAIR LOG