Document Outline

• Section 1. SAFETY
  • 1.1 General
    • Operator Training and Knowledge
  • 1.2 Towing Regulations
  • 1.3 Before Operating the Lift
    • Workplace Inspection
    • Machine Inspection
  • 1.4 Operation
    • General
    • Trip and Fall Hazards
    • Electrocution Hazards
    • Tipping Hazards
    • Crushing and Collision Hazards
  • 1.5 Lifting, and Hauling
  • 1.6 Towing Hazards
  • 1.7 Additional Hazards / Safety
• Section 2. USER RESPONSIBILITIES, MACHINE PREPARATION, AND INSPECTION
  • 2.1 Personnel Training
    • Operator Training
    • Training Supervision
    • Operator Responsibility
  • 2.2 Preparation, Inspection, and Maintenance
    • Pre-Start Inspection
    • Function Check
• Section 3. TOWING
  • 3.1 General Towing information
  • 3.2 Coupler
  • 3.3 Tow Vehicle And Hitch Information
    • Towing Hitch
  • 3.4 Coupling and Uncoupling the Trailer
    • Before Coupling the Trailer to Tow Vehicle
    • Tongue Height
    • Coupler and Ball
    • Tongue Jack
    • Coupling the Trailer to the Hitch
    • Uncoupling the Trailer from the Hitch
    • Rigging Safety Chains (If equipped)
    • Testing Breakaway Brake
    • Connect the Electrical Cables
  • 3.5 Engaging Manual Lockout Lever
  • 3.6 Trailer Maneuvering
  • 3.7 Towing Guidelines
  • 3.8 Pre-Tow Inspection
• Section 4. MACHINE CONTROLS AND INDICATORS
  • 4.1 General
  • 4.2 Controls and Indicators
    • Ground Control Station
    • Platform Station
• Section 5. MACHINE OPERATION
  • 5.1 Description
  • 5.2 Boom Operating Characteristics and Limitations
    • Capacities
    • Stability
  • 5.3 Engine Operation (If Equipped)
    • Starting Procedure
    • Shutdown Procedure
    • Fuel Valve Lever
  • 5.4 Outriggers
    • From the Ground Console
    • From the Platform Console (Drive & Set Only)
  • 5.5 Platform
    • Platform Level Adjustment
    • Platform Rotation (If Equipped)
  • 5.6 Boom
    • Swinging the Boom
    • Raising and Lowering the Boom
    • Telescoping the Boom
  • 5.7 Jib Lift
  • 5.8 User Fault Codes
  • 5.9 Battery Charging
    • Battery Charger Fault Codes
  • 5.11 Platform Removal & Installation
  • 5.12 Material hook Installation
  • 5.13 Material Hook Operating Precautions
  • 5.14 Accessory Tray
  • 5.15 Panel Tray
  • 5.16 Drive & Set
    • To Set Up The Machine for Drive & Set Operation:
    • To Prepare the Machine For Towing After Drive & Set Operation:
  • 5.17 Shut Down and Park
  • 5.18 Tie Down
• Section 6. EMERGENCY PROCEDURES
  • 6.1 General
  • 6.2 Incident Notification
  • 6.3 Emergency Operation
    • Operator Unable to Control Machine
    • Platform or Boom Caught Overhead
  • 6.4 Manual Descent
    • Lift Down
    • Telescope In
    • Telescope Out
    • Swing
    • Platform Jib
• Section 7. GENERAL SPECIFICATIONS & OPERATOR MAINTENANCE
  • 7.1 Introduction
  • 7.2 Operating specifications
    • Dimensional Data
    • Fluid Capacities
    • Electric Power Unit
    • Taillight and Marker Light Bulb Information (ANSI Machines)
    • Tires
    • Engine
    • Batteries (Electric Machines)
    • Component Weights
    • Lubrication
  • 7.3 Operator Maintenance
  • 7.4 Tires & Wheels
    • Glossary of Tire and Loading Terminology
    • Basic Tire Maintenance
    • Tire Inflation
    • Tire Wear
    • Tire Repair
    • Tire Replacement
    • Tire Fundamentals
    • Wheel Replacement
    • Wheel Installation
    • Lug Nuts (Bolts)
    • Unsealed Wheel Bearings (Hubs)
  • 7.5 Supplemental Information
• Section 8. INSPECTION AND REPAIR LOG