Document Outline

• 1794-UM061A-EN-P FLEX I/O Diagnostic Modules User Manual
  • Important User Information
  • Preface
    • Purpose of This Manual
    • Important Warnings and Cautions
      • North American Hazardous Location Approval
    • Related Products and Documentation
  • Chapter 1 - 1794 FLEX I/O Diagnostic Digital Modules Overview
    • Introduction
    • General Description
      • Network Compatibility
      • 1794-IB16D Diagnostic Input Module Compatibility
      • 1794-OB16D Diagnostic Output Module Compatibility
    • Install Your Digital Input or Output Module
  • Chapter 2 - About the FLEX I/O Diagnostic Input Module
    • Introduction
    • About the 1794-IB16D Diagnostic Input Module
      • Wiring Input Sensors
    • Diagnostic Fault Detection
      • Sensor Power Open and Short Circuit Detection
      • User Power Supply Reverse Voltage Detection
      • User Power Supply Loss Detection
    • Indicator Status Information
    • Module Limitations
      • Input Voltage Derating
      • Sensor-Power Derating
      • Unused Sensor Power Ports
      • Open Contact Mechanical Switches and Relays
      • Sensor Power Internal Voltage Drop
    • Configure Your Diagnostic Input Module
      • Input Filter Times
  • Chapter 3 - About the FLEX I/O Diagnostic Output Module
    • Introduction
    • About the 1794-OB16D Diagnostic Output Module
      • Wiring Output Loads
    • Diagnostic Fault Detection
    • Module Protection Functions
      • Output Fault & Idle States With Network Communication Failure
      • Indicator Status Information
    • Module Limitations
      • Unused Output Channels
    • Configure Your Output Diagnostic Module
  • Chapter 4 - Configuring Modules for Communication on a Remote I/O Network
    • Chapter Objectives
    • Add a 1756-DHRIO Module
    • Add a 1794 Remote Adapter Module
    • Configure Digital Modules
    • Create a Block Transfer (Read or Write) Message Instruction
    • Ladder Logic Examples
  • Chapter 5 - Configure FLEX I/O Digital Modules on a DeviceNet Network
    • How to Use This Chapter
    • Add the Scanner to the I/O Configuration of the Controller Using RSLogix 5000 Software
      • If You Need to Conserve EtherNet/IP or ControlNet Network Bandwidth
      • Add the Scanner to the I/O Configuration Folder
      • Define the Properties of the Scanner
    • Determine the Address of DeviceNet Data
    • Tally Memory Requirements
    • If You Configure the Adapter Offline
    • Set the Address of the Adapter
  • Chapter 6 - Configure Your Adapter and Digital Modules on a ControlNet Network
    • Introduction
    • Set Up the Hardware
    • Setting a Requested Packet Interval (RPI)
    • Select a Communication Format
      • Direct or rack-optimized connection
      • Ownership
    • Add Local and Remote ControlNet Modules
    • Add Distributed I/O
    • Download the Program to the Controller
    • Configure the 1794-ACN15 Adapter
    • Schedule I/O Module Connections
    • Access Module Data via the 1794-ACN15 Adapter
      • Slot Status Bits
    • Change Configuration Data
  • Chapter 7 - Configure your Digital Module on an EtherNet/IP Network
    • How to Use This Chapter
    • Set Up the Hardware
    • Select a Requested Packet Interval (RPI)
    • Select a Communication Format
      • Choose Direct or Rack-optimized Connection
      • Ownership
      • Select a Remote Adapter
    • Add Distributed I/O
      • Add a Module
    • Download the Program to the Controller
    • Access Distributed I/O
    • General Information About IP Addresses
      • Determining Required Network Parameters
    • Assigning Network Parameters via the BOOTP/DHCP Utility
    • Using Other Methods to Assign Network Parameters
      • Using RSLinx software to set the IP address
      • Using RSLogix 5000 software to set the IP address
      • Using DHCP software to set the IP address
    • Duplicate IP Address Detection
      • Duplicate detection scenarios
    • IP Address Swapping
  • Appendix A - Interpret the Indicators
    • Introduction
    • About the Indicators
    • 1794-IB16D Diagnostic Functional Details
      • Diagnostic Capabilities
      • Diagnostic Functions for the 1794-IB16D
    • 1794-OB16D Diagnostic Functional Details
      • Diagnostic Functions for the 1794-OB16D
  • Appendix B - Simplified Schematics of FLEX I/O Digital Modules
    • Find Your Module
      • 1794-IA8 120V AC 8 Input Module
      • 1794-IA8I 120V AC 8 Input Module
      • 1794-IA16 120V AC 16 Input Module
      • 1794-OA8 120V AC 8 Output Module
      • 1794-OA8I 120V AC 8 Output Module
      • 1794-OA16 120V AC 16 Output Module
      • 1794-IM 8 220V AC 8 Input Module
      • 1794-OM8 220V AC 8 Output Module
      • 1794-IB8 24V DC 8 Input Module
      • 1794-IB16 24V DC 16 Input Module
      • 1794-IB16D 24V DC 16 Diagnostic Input Module
      • 1794-IB32 24V DC 32 Input Module
      • 1794-IB10XOB6 24V DC 8 10 Input/6 2A Output Module
      • 1794-IB16XOB16P 24V DC 16 Input/16 Output Module
      • 1794-IV16 24V DC 16 Source Input Module
      • 1794-OB8 24V DC 8 Output Module
      • 1794-OB8EP 24V DC Electronically Protected 8 Output Module
      • 1794-OB16 24V DC 16 Output Module
      • 1794-OB16D 24V DC 16 Diagnostic Output Module
      • 1794-OB16P 24V DC 16 Output Module
      • 1794-OB32P 24V DC 32 Output Module
      • 1794-OV16 24V DC 16 Sink Output Module
      • 1794-OV16P 24V DC 16 Sink Output Module
      • 1794-IC 48V DC 16 Input Module
      • 1794-OC 48V DC 16 Output Module
      • 1794-OW8 Relay Output Module
    • Index
      • Numerics
      • A
      • C
      • D
      • F
      • G
      • H
      • I
      • M
      • N
      • O
      • R
      • S
      • Z
    • How Are We Doing?
• Back Cover