MITSUBISHI ELECTRIC DX-TL1600EM - Manual (Page 3)

ENGLISH
3
••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••• Beginning
NEVER TOUCH OR INSERT ANY OBJECT INSIDE THE UNIT
Touching the inside of the cabinet or inserting foreign objects of any kind not only creates a safety hazard but can also
cause extensive damage.
PROTECT THE POWER CORD
Damage to the power cord may cause fire or shock hazard. If the mains cord is damaged, switch off the mains outlet
and carefully unplug the cord by holding the mains plug.
UNPLUG THE POWER CORD DURING A LONG ABSENCE
Turn off the power and unplug the power cord during a long absence.
MAINTAIN GOOD VENTILATION
Do not obstruct the many ventilation holes on the unit. For maximum ventilation, leave some space around the unit and
place the unit on a hard level surface only, and ensure it is not covered during use. Heavy objects should never be placed
on the unit.
WHEN NOT IN USE
When not in use always turn OFF the unit's POWER.
CABINET CARE
Never use petroleum-based cleaners. Clean with a soft cloth moistened with soap and water and wipe dry.
PVC cables or leads should not be left in contact with the cabinet surface for long periods.
ATTACHING THE FERRITE CORE
The ferrite core is essential to avoid radio interference from the cables connected the unit against peripheral device. Be sure
to attach the ferrite core to all cables connected to ALARM IN terminals (GND terminals) and I/O terminals.
INSTALLATION LOCATION
For excellent performance and lasting reliability install in a location that is:-
1.
Well ventilated, out of direct sunlight and away from direct heat.
2. A solid vibration-free surface.
3. Free from high humidity, excessive dust and away from magnetic fields.
4. Please ensure that the ventilation fan located on the unit’s back panel is not blocked.
UNSUITABLE LOCATIONS
Placing the unit in the following places might shorten the product life:
•
Extremely cold places, such as refrigerated warehouses and ice houses
• Places where excessive hydrogen sulfide is likely to be generated, such as hot-springs areas
• Places or locations with salt air environment.
WARNING: TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS APPARATUS TO RAIN OR
MOISTURE. THIS APPARATUS MUST BE GROUNDED.
HEAVY OBJECTS SHOULD NEVER BE PLACED ON THE UNIT (E.G., TV)
Caution and care
This Unit complies with the requirements of the EC Directive 89/336/EEC, “EMC Directive” , as amended by Directive
93/68/EEC. The requirements for the susceptibility according to EN 55024 and the requirements for interference
according to EN 55022 are observed for the operation on residential areas, business, light industrial premises and in
small scale enterprises, inside as well as outside of the building. All places of operation are characterised by their
connection to the public low voltage power supply system. This unit is manufactured in accordance with EN 60950.
The user will not be indemnified for problems (e.g., recording failure or playback failure) that occur with either the
unit or a connected device during operation. It is recommended that backups of important recordings are made
regularly as a precaution against possible breakdowns and accidents.
There may be cases when the unit’s built-in MOTION DETECTION function does not operate properly due to
external condition or video input signal or other factors.
MAINS LEAD CONNECTION
The mains lead on this Unit is fitted with a non-rewireable mains plug, incorporating a 5A fuse. If you need to
replace the fuse, use a 5A fuse approved by BSI or ASTA to BS 1362, ensuring you refit the fuse cover. If the
mains plug is not suitable for the sockets in your home, and you require to remove the plug, remove the fuse, cut
off the plug then dispose of the plug immediately, to avoid a possible electric shock hazard. To refit a new plug,
follow these instructions; Green-and-yellow: Earth, Blue: Neutral and Brown: Live.
As the colours in the mains lead of this Unit may not correspond with the coloured markings identifying the
terminals in your plug, proceed as follows.
•The wire which is coloured green-and-yellow must be connected to the terminal in the plug which is marked by
the letter E or by the safety earth symbol
» or coloured green or green-and-yellow.
•The wire which is coloured blue must be connected to the terminal which is marked with the letter N or coloured black.
•The wire which is coloured blown must be connected to the terminal which is marked with the letter L or coloured red.