MITSUBISHI ELECTRIC DX-TL1600EM - Manual (Page 58)

58
••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••
Can not change the display, during the search
selection menu will appear.
6. To play back search results.
• Press either the PLAY button or the PAUSE button.
Refer to page 56 for details on Various playback
functions.
To exit the <INDEX SEARCH> menu without ac-
tivating the search, press the SEARCH button on
the front of the unit.
7. Press the STOP button to stop playback and still frame mode.
• Press the SEARCH button, the display will revert to its
original state.
♦ How to count index signals
Present time in the diagram below represents the point of
playing back or stopped playing back. To search index with
“ +”, turn the SHUTTLE ring to the right to search forward.
To search index with “ - ”, turn the SHUTTLE ring to the left
to search backward.
Present position
Beginning of playback device End of playback device
-15 -1 -2 +1 +15 +2
A•REC A•REC A•REC A•REC A•REC A•REC
A•REC: Alarm Recording
■ Skip Search
Skip Search is a process where the unit automatically
searches for an index signal, then retrieves the visuals
associated with that index and plays back the images for 5
seconds each to select the camera number.
To play back search results, press the PLAY but-
ton for the desired image.
1. Press the SEARCH button to display by the <SEARCH
SELECTION> menu. Setting the <SELECTION CAMERA NO.>
menu, repeat the steps 2, 3 of the INDEX SEARCH setting
procedures.
2. Turn the JOG dial to select the SKIP SEARCH, and turn the
SHUTTLE ring to the right.
• The <SKIP SEARCH> menu will appear .
<SEARCH SELECTION>
SELECTION CAMERA NO. 5
TIME DATE SEARCH
INDEX SEARCH
@SKIP SEARCH
ALARM LIST SEARCH
JUMP TO START POINT
3. Turn the SHUTTLE ring to desired direction (Forward search
to the right and reverse to the left).
• The unit begins the Index Search, and plays back the images
associated to the index for five seconds each. Playback is
displayed on a SPLIT 16 screen when “ALL” is selected in
the SELECTION CAMERA NO. setting, and displayed on a
single screen when an individual camera number is selected.
<SKIP SEARCH> 5
TURN THE SHUTTLE RING
<< OR >> TO
PREVIEW EACH ALARM.
Using the backup device/copy device
Various search (continued)
The unit cannot be selected to single screen dis-
play mode during Skip Search.
4. Press the STOP button to stop searching.
When reverse SKIP SEARCH is used on recorded
content that includes five seconds or less of alarm
recording, those five seconds or less of alarm re-
cording may be played back repeatedly. If this hap-
pens, press the stop button to halt SKIP SEARCH,
use reverse playback to get past the content being
played back repeatedly, and then resume with re-
verse SKIP SEARCH.
■ Alarm List Search
When Alarm Recording is initiated (refer to page 53), the
Alarm Recording start time will be added to the Alarm List.
Alarm List Search is a process which uses the associated
Alarm Recording start time to retrieve a desired image for
still frame playback to select the camera number.
Up to 800 Alarm Recording start-times can be
registered. After the 800th time, the first start-time
will be erased and the 801st start-time will be added
to the list.
1. Press the SEARCH button to display by the <SEARCH
SELECTION> menu. Setting the <SELECTION CAMERA NO.>
menu, repeat the steps 2, 3 of the INDEX SEARCH setting
procedures.
2. Turn the JOG dial to select the ALARM LIST SEARCH, and
turn the SHUTTLE ring to the right.
• The <ALARM LIST SEARCH> menu will appear .
<SEARCH SELECTION>
SELECTION CAMERA NO. 5
TIME DATE SEARCH
INDEX SEARCH
SKIP SEARCH
@ALARM LIST SEARCH
JUMP TO START POINT
3. Turn the JOG dial till the cursor goes to desired alarm list
number, then turn the SHUTTLE ring to the right.
• The unit begins the Alarm List Search, and retrieves the
image associated with the selected time (or the time closest
to the selected time).
• Playback is displayed on a SPLIT 16 screen when “ALL” is
selected in the SELECTION CAMERA NO. setting, and
displayed on a single screen when an individual camera
number is selected.
<ALARM LIST SEARCH>
No.
0003
0002
0001 TIME
18:54:25
18:34:40
18:20:00 DATE
26-01-01
26-01-01
25-01-01 C
5
5
5
@
The JOG dial can be used to move the cursor
line-by-line through the list. When the cursor reaches
either the top or the bottom of the list, the <ALARM
LIST SEARCH> menu will scroll to the next page.
To move through the pages, place the cursor over
“No.”, and turn the SHUTTLE ring.