Sanyo DSR-5716P - Manual (Page 101)

100
English
RECORD SET 2
INTRODUCTION
SE
TTINGS
NE
T
W
O
R
K
CO
NT
RO
L
NETW
ORK
O
P
E
RATION
NE
T
W
ORK
S
E
TTINGS
OTHE
R
OPE
RATION
10
Turn the shuttle dial clockwise.
“ONLY” flashes.
11
Turn the jog dial to select the “ALARM
INTERLEAVE” setting and then turn the
shuttle dial clockwise.
The cursor moves to “REC RATE/DURATION”.
[Settings] (‹ indicates default setting)
* Example of recording pattern for SW and ONLY
12
Turn the shuttle dial clockwise.
If “ALARM INTERLEAVE (Step 11)” is set to other than
program mode, you see “A12.5FPS” flash for “REC RATE”,
which indicates setting is acceptable.
13
Turn the jog dial to select the “REC
RATE” setting and then turn the shuttle
dial clockwise.
The cursor moves to “DURATION”.
[Settings] (‹ indicates default setting)
z If “ALARM INTERLEAVE (Step 11)” is set to program
mode, you see “****” displayed and can not select
recording rate.
Setting Description
‹ ONLY
Video is recorded only from cameras with an
alarm occurring.
SW
Recording is switched between video from a
camera for which an alarm has occurred and
video from all connected cameras.
ALL
Video recording for all the connected cameras
by turns starts, when any one of the cameras
receives an alarm.
ONLY (P-1)
ONLY (P-2)
ONLY (P-3)
ONLY (P-4)
<Program mode for “ONLY”>
When a connected camera registered in the
program recording setting receives an alarm,
video recording starts at a recording rate
specified in the program.
z
Specify a program you want to apply from
“P-1 to P-4.”
z Audio recording is not available.
ALL (P-1)
ALL (P-2)
ALL (P-3)
ALL (P-4)
<Program mode for “ALL”>
When any one of the connected cameras
registered in the program recording setting
receives an alarm, video recording starts for all
the connected cameras at a recording rate
which was independently specified for each
connected camera in the program.
z
Specify a program you want to apply from
“P-1 to P-4.”
z Audio recording is available only when any
one of the cameras has a recording rate of 1
FPS or more.
<ALARM REC MODE SET>
ALARM RECORDING : ENABLED
PICTURE QUALITY : ENHANCED
PICTURE QUALITY SET ->
AUDIO RECORDING : ON
ALARM INTERLEAVE : ONLY
REC RATE:A12.5FPS, DURATION: 20SEC
PRE-ALARM RECORDING : OFF
REC RATE: ***** FPS, DURATION: *****
ALARM TRIGGER : ALARM
MOTION SENSOR ->
<ALARM REC MODE SET>
ALARM RECORDING : ENABLED
PICTURE QUALITY : ENHANCED
PICTURE QUALITY SET ->
AUDIO RECORDING : ON
ALARM INTERLEAVE : ONLY
REC RATE:A12.5FPS, DURATION: 20SEC
PRE-ALARM RECORDING : OFF
REC RATE: ***** FPS, DURATION: *****
ALARM TRIGGER : ALARM
MOTION SENSOR ->
Setting Description
50, 25, 16.67, ‹12.5,
8.333, 6.25, 5, 4.167,
3.571, 3.125, 2.778, 2.5,
2.273, 1.923, 1.667,
1.471, 1.316, 1.19, 1.087,
1, 0.5, 0.333, 0.25, 0.2,
0.1, 0.05, 0.033
Recording is performed at the
selected recording rate (unit: FPS).
02 02 02 02 02 02 01 03 04
02 02 02 02 02 01 03 04 04 04 05 06 07 08
Alternate recording of multiple alarm recordings
Recording until alarm is cancelled
Alarm Alarm
Alarm Alarm is cancelled
SW
ONLY
<ALARM REC MODE SET>
ALARM RECORDING : ENABLED
PICTURE QUALITY : ENHANCED
PICTURE QUALITY SET ->
AUDIO RECORDING : ON
ALARM INTERLEAVE : ONLY
REC RATE:A12.5FPS, DURATION: 20SEC
PRE-ALARM RECORDING : OFF
REC RATE: ***** FPS, DURATION: *****
ALARM TRIGGER : ALARM
MOTION SENSOR ->
<ALARM REC MODE SET>
ALARM RECORDING : ENABLED
PICTURE QUALITY : ENHANCED
PICTURE QUALITY SET ->
AUDIO RECORDING : ON
ALARM INTERLEAVE : ONLY
REC RATE:A12.5FPS, DURATION: 20SEC
PRE-ALARM RECORDING : OFF
REC RATE: ***** FPS, DURATION: *****
ALARM TRIGGER : ALARM
MOTION SENSOR ->