Advanced menu set 8, Camera control settings – Sanyo DSR-5716P User Manual
Page 151
150
English
ADVANCED MENU SET
8
INTRODUCTION
SE
TTINGS
NE
T
W
O
R
K
CO
NT
RO
L
NETW
ORK
O
P
E
RATION
NE
T
W
ORK
S
E
TTINGS
OTHE
R
OPE
RATION
Settings are required when a remotely controllable camera(s)
is connected with the digital video recorder.
With connection made by following the procedure below, you
can control a camera(s) in the full screen mode.
Connections necessary for remote operation:
z
Connect coaxial control cameras to the VIDEO terminal.
z
Connect the Sanyo RS-485 control camera to the RS-485
(RJ-11) terminal.
z
Connect another maker’s RS485/422 control camera to the
2ND RS485/422 terminal.
z
If “ADDRESS” in the <RS-485 SET> screen (JP.121) is
set to between “001” and “008”, camera control settings
can be performed. Camera control settings are not
available if “ADDRESS” is set to “000” or between “009”
and “127”.
z
Before configuring trigger actions, be sure to configure
the settings under “ALARM REC MODE SET” and
“PROTOCOL/ADDRESS SET”.
1
Press the [MENU] button.
The MENU indicator lights up and the <MAIN MENU> is
displayed.
2
Turn the jog dial to select
“8.ADVANCED MENU SET” and then
turn the shuttle dial clockwise.
The <ADVANCED MENU SET> screen is displayed.
3
Turn the jog dial to select “3.CAMERA
CONTROL SET” and then turn the
shuttle dial clockwise.
The <CAMERA CONTROL SET> screen is displayed.
4
Turn the jog dial to select
“1.PROTOCOL/ADDRESS SET” and
then turn the shuttle dial clockwise.
The <PROTOCOL/ADDRESS SET> screen is displayed.
5
Turn the jog dial to select the camera
number corresponding to a connected
dome camera and then turn the shuttle
dial clockwise.
“OFF” flashes for “PROTOCOL”.
On the DSR-5709P, cameras No. 01-09 are displayed.
6
Turn the jog dial to select a protocol and
then turn the shuttle dial clockwise.
The cursor moves to the next camera number.
[Settings] ( indicates default setting)
Camera control settings
MENU
<CAMERA CONTROL SET>
1. PROTOCOL/ADDRESS SET ->
2. ALARM REC TRIGGER SET ->
Setting
Description
OFF
No protocol
SANYO RS485
SANYO RS485
BBV COAX
BBV COAX
(Also supports AUX commands.)
PELCO COAX
PELCO COAX
2ND RS-485/422
2ND RS-485/422
COAX (H-SSP)
COAX (H-SSP)
<PROTOCOL/ADDRESS SET>
CH PROTOCOL ADD. CH PROTOCOL ADD.
01 OFF --- 09 OFF ---
02 OFF --- 10 OFF ---
03 OFF --- 11 OFF ---
04 OFF --- 12 OFF ---
05 OFF --- 13 OFF ---
06 OFF --- 14 OFF ---
07 OFF --- 15 OFF ---
08 OFF --- 16 OFF ---
2ND RS-485/422 PROTOCOL : OFF 9600bps
<PROTOCOL/ADDRESS SET>
CH PROTOCOL ADD. CH PROTOCOL ADD.
01 OFF --- 09 OFF ---
02 OFF --- 10 OFF ---
03 OFF --- 11 OFF ---
04 OFF --- 12 OFF ---
05 OFF --- 13 OFF ---
06 OFF --- 14 OFF ---
07 OFF --- 15 OFF ---
08 OFF --- 16 OFF ---
2ND RS-485/422 PROTOCOL : OFF 9600bps
<PROTOCOL/ADDRESS SET>
CH PROTOCOL ADD. CH PROTOCOL ADD.
01 SANYO RS-485 001 09 OFF ---
02 OFF --- 10 OFF ---
03 OFF --- 11 OFF ---
04 OFF --- 12 OFF ---
05 OFF --- 13 OFF ---
06 OFF --- 14 OFF ---
07 OFF --- 15 OFF ---
08 OFF --- 16 OFF ---
2ND RS-485/422 PROTOCOL : OFF 9600bps