Symmetricom XLi IEEE 1588 User Manual
Xli ieee 1588 clock
Advertising
Table of contents
Document Outline
- Notices
- Table of Contents
- 1: Overview and Features
- 2: System Specifications
- 3: Installation and Set-up
- 4: User Interfaces
- 5: Function Reference
- Function Summary
- F1 - Time Zone Offset
- F2 - 12/24 Hour Format
- F3 - Time & Date
- F4 - Serial Port Configuration
- F5 - Time-Quality Setup
- F6 - Keypad Lock
- F8 - Continuous Time Once-per-Second
- F9 - Time On Request
- F11 - Time Output Format
- F13 - Time Error
- F18 - Software Version Request
- F27 - FTM III Configuration
- F42 - Multicode Output Configuration
- F44 - N.8 Frequency Synthesizer
- F50 - GPS Receiver LLA/XYZ Position
- F51 - GPS Antenna Cable Delay
- F52 - Distribution Cable Delay
- F53 - GPS Operation Mode
- F60 - GPS Receiver Satellite List
- F66 - Daylight Saving Time (DST) Mode
- F69 - Time Mode
- F71 - Oscillator Statistics
- F72 - Fault Status
- F73 - Alarm Control / Status
- F74 - Clock Source Control
- F90 - Code Output Configuration
- F100 - Network Port Configuration & XLi Firmware
- F100 EA - Ethernet Address
- F100 IP - IP Address
- F100 SM - Subnet Mask
- F100 G - Gateway
- F100 IC - Network Port Settings
- F100 BASET - 10/100 BASE- T
- F100 L/LOCK/UNLOCK - Remote Lockout
- F100 L - Remote Lockout
- F100 ST - Self Test Status
- F100 BH - Burn Host
- F100 BUB - Burn BootLoader
- F100 BU - Burn
- F100 BF - Burn File System
- F100 BUFP - Burn FPGA Firmware
- F100 CONFIG - Configure NTP & SNMP
- F100 J - Factory Mode Jumper
- F100 K I L L - Reboot
- F100 P - Change User Password
- F100 PI - PING
- F100 PN - Change User Name
- F108 - Oscillator Configuration
- F110 - J1 Input (TIET)
- F111 - J2 Output (Rate)
- F113 - J3 Input Configuration (Aux Ref)
- F116 - Display Brightness Level
- F117 - Factory Configuration
- F118 - Option Board Configuration
- F119 - GPS Receiver Configuration
- F120 - N.1 Frequency Synthesizer
- F123 - Have Quick Input/1 PPS Sync Configuration
- F126 - Options Key Entry
- F128 - Have Quick Output
- F130 - Precision Time Protocol Status
- F131 - Precision Time Protocol Network Config
- Option bay location of the IEEE 1588 cards
- Static IP address, subnet mask and default gateway for the network port
- DHCP enabled/disabled
- DHCP-assigned IP address, subnet mask and default gateway for the network port
- PTP Sync message interval
- PTP burst mode enabled/disabled
- PTP network port enabled/disabled
- PTP subdomain same
- Reset PTP settings to factory defaults
- PTP initialize to user entered values
- PTP Master or Slave (PRI/SEC/STBY)
- PTP Slave Synchronization Threshold
- PTP Preferred Master Configuration
- Request a summary of the PTP card configuration
- Set Internet Configuration settings
- Set the IP Address
- Set the Subnet Mask
- Set the Default Gateway
- Setting the Internet Configuration
- Enable/Disable DHCP
- Get PTP Protocol settings
- Request the PTP Subdomain Name
- Set the PTP Subdomain Name
- Reset the PTP Parameters to the Factory Default settings
- Initialize the PTP Protocol to User-entered Values
- Configuring the PTP Reference Clock Settings
- Request the PTP Slave Synchronization Threshold
- Set the PTP Slave Synchronization Threshold
- Request the PTP Preferred Master Clock Configuration
- Enable or Disable the PTP Preferred Master Clock Configuration
- Request PTP Network Parameter Status
- 9: XLi-Generated Messages
- A: Using F100 Configuration
- B: Upgrading System Firmware
- C: SNMP
- E: Time Code Formats
- F: World Map of Time Zones:
- G: Part Numbers
- H: Sales and Customer Assistance
- Glossary of IEEE 1588-related Terms
- Index