AUMA Electric multi-turn actuators SA 07.1 - 16.1_SAR 07.1 - 16.1 MATIC AM 01.1 - 02.1 User Manual

Electric multi-turn actuators

Advertising

Electric multi-turn actuators

Operation instructions

SA 07.1 – SA 30.1

SAR 07.1 – SAR 30.1

with actuator controls

AUMA MATIC AM 01.1 / AM 02.1

for flange type FA

Advertising

Table of contents

Document Outline

Table of contents
1. Safety instructions
- 1.1 Range of application
- 1.2 Electrical connection
- 1.3 Maintenance
- 1.4 Warnings and notes
2. Short description
3. Technical data
4. Additional information to the wiring diagram legend
5. Transport, storage and packaging
- 5.1 Transport
- 5.2 Storage
- 5.3 Packaging
6. Mounting to valve/ gearbox
7. Mounting positions of the local controls
8. Electrical connection
- 8.1 Connection with AUMA plug/ socket connector (S, SH, SE)
9. Manual operation
10. Operation and indications of the local controls
11. Opening the switch compartment
- 11.1 Removing the cover from the switch compartment
- 11.2 Pulling off the indicator disc (option)
12. Setting the limit switching
- 12.1 Setting end position CLOSED (black section)
- 12.2 Setting end position OPEN (white section)
- 12.3 Checking the limit switches
13. Setting the DUO limit switching (option)
- 13.1 Setting direction CLOSE (black section) .Move valve
- 13.2 Setting direction OPEN (white section)
- 13.3 Checking the DUO limit switches
14. Setting the torque switching
- 14.1 Setting
- 14.2 Checking the torque switches
15. Test run
- 15.1 Checking the direction of rotation
- 15.2 Checking the setting of the limit switching
- 15.3 Checking the type of seating
- 15.4 Checking the PTC tripping device (option)
16. Setting the potentiometer (option)
17. Setting the electronic position transmitter RWG (option)
- 17.1 Setting 2-wire system 4 – 20 mA and 3- /4-wire system 0 – 20 mA
- 17.2 Setting 3- / 4- wire system 4 – 20 mA
18. Setting the mechanical position indicator (option)
19. Closing the switch compartment
20. Actuator controls AUMA MATIC
- 20.1 Functions of the diagnosis LEDs on the interface board (standard version)
- 20.2 Programming the logic board
- 20.3 EMERGENCY - OPEN and EMERGENCY - CLOSE signal (option)
21. Electronic positioner (option)
- 21.1 Technical data
- 21.2 Setting
  - 21.2.1 Setting type of signal
  - 21.2.2 Setting actuator behavior on loss of signal
- 21.3 Positioner adjustment for end position CLOSED (standard version)
- 21.4 Positioner adjustment for end position OPEN (standard version)
- 21.5 Setting the sensitivity
- 21.6 Positioner adjustment for end position OPEN (inverse operation)
- 21.7 Positioner adjustment end position CLOSED (inverse operation)
- 21.8 Positioner in Split Range version (option)
22. Timer (option)
- 22.1 Functions of the diagnosis LEDs (timer)
- 22.2 Setting start and end of stepping mode via DUO limit switching (option)
- 22.3 Setting ON and OFF times
23. Fuses
- 23.1 Fuses within the actuator controls
- 23.2 Motor protection
24. Enclosure protection IP 68 (option)
25. Maintenance
26. Lubrication
27. Disposal and recycling
28. Service
29. Spare parts list Multi-turn actuator SA 07.1 – SA 16.1/SAR 07.1 – SAR 16.1
30. Spare parts list controls AUMA MATIC
Index
- A
  - Ambient temperature 8
- B
  - Blinker transmitter 35
- C
- D
- E
- F
  - Finish machining of the stem nut 13
  - Fuses 52
- H
  - Handwheel 19
  - Heater 15
- I
- L
- M
- N
  - Name plate 61
- O
  - Output drive types 12
  - Overvoltage category 6
- P
- R
- S
- T
- W
  - Wall bracket 16

Popular Brands

Popular manuals