Document Outline

• Installing the Modem
  • Step 1— Unpack the Modem
  • Connect the 10BaseT Port
  • LED Status Indications
• Accessing the WebInterface for Modem Management
  • Step 1— Assign IP Addresses
• Configuring the LAN
  • Before You Begin. . .
  • Configure the LAN
  • Configure DNS Relay Mode
  • Configure DHCP Server Mode
  • Configure the Ethernet Port Mode
• Configuring the WAN
  • Before You Begin. . .
  • Configure a New WAN Session
    • Set Up an RFC 1483 Bridged Session
    • Set Up an RFC 1483 Routed Session
    • Set Up a PPPoA or PPPoE Routed Session
    • Permanently Save Sessions
  • Edit a WAN Session
• Configuring SystemParameters
  • Before You Begin. . .
  • Assigning User Access
  • Add a Default Gateway
  • Add Static Route Entries
  • Add SNMP Communities
  • Change Spanning Tree Setting
  • Saving Changes
  • Rebooting the Modem
• Configuring DSL Parameters
  • Before You Begin. . .
  • Complete a G.shdsl Quick Configuration
  • Complete a DSL Advanced Configuration
• Implementing a Point-to-Point LAN Extension
  • Before You Begin. . .
  • Complete a Quick Installation
    • Configure for CentralOffice Mode
    • Change the LAN IP Address for the CentralOffice Modem
  • Complete a Custom Configuration
    • Configure the Remote Modem
      • Configure the Remote Operating Mode
      • Configure the Remote WAN
      • Configure the Remote LAN
    • Configure the CentralOffice Modem
      • Configure the CentralOffice Operating Mode
      • Configure the CentralOffice WAN
      • Configure the CentralOffice LAN
  • Verify Connectivity
• Configuring Modem Security
  • Before You Begin. . .
  • Configure NAT
• Managing the Modem
  • View System Status
    • View Modem Status
    • View System Log
  • View WAN Statistics
  • View LAN Statistics
  • View SmartCNCT Security Statistics
  • View ATM Statistics
  • View DSL Statistics
    • View G.shdsl Link Statistics
    • View G.shdsl Error Counters
  • Manage Software and Configuration
    • Update System Software
    • Reset to Factory Defaults
• Accessing the CommandLineInterface
  • Connect to the Console Port
  • Access the CommandLine Interface
    • Access through the Console Port
    • Access through a Telnet Session
  • Set Up the LAN
  • Manage WAN Sessions
    • Add a New Session
      • Set Up an RFC 1483 Bridged Session
      • Set Up an RFC 1483 Routed Session
      • Set Up a PPPoA or PPPoE Routed Session
    • Permanently Save Sessions
    • Edit an Existing Session
  • Manage DSL
    • Configure G.shdsl Parameters
      • Complete a Quick Configuration
      • Complete an Advanced Configuration
    • View G.shdsl Configuration
    • Monitor G.shdsl Statistics
      • View G.shdsl General Statistics
      • View G.shdsl General Statistics
      • View ATM Counters
  • Restoring Factory Defaults
  • Saving the Current Configuration
  • Updating System Software
  • Viewing System Information
  • Rebooting the Modem
• Specifications
  • Overview
  • Data Specifications
    • VLAN Support
    • DSL Standards
    • ATM standards
    • Internetworking Features
    • WAN Protocols
    • Security
    • Management
    • Software Upgrade
    • Encapsulation
    • RFCs
    • MIBs
    • Default Session Parameter Values
  • Hardware Specifications
    • LED
    • Connectors
    • LAN Interface
    • WAN Interface
    • Connector Pinouts
      • DSL Port (RJ-11)
      • 10Base-T Port (RJ-45)
      • Console Port (RJ-45)
  • Rate vs. Reach
• Contacting ADC
• Glossary