Document Outline

• 1746-UM010B-EN-P
• Important User Information
• European Communities (EC) Directive Compliance
  • EMC Directive
  • Low Voltage Directive
• Summary of Changes
• Preface
  • Using This Manual
    • Audience
    • System Compatibility
  • Vocabulary
• Table of Contents
• 1 - Getting Started
  • Temperature Control Using a BTM Module in an SLC System
  • Features of the Temperature Control Module
  • Module Outputs
    • Current CV
    • TPO
  • Module Addressing
  • Response to Slot Disabling
    • Input response
    • Output response
  • Chapter 2
• 2 - Installing and Wiring
  • Avoiding Electrostatic Damage
  • European Communities (EC) Directive Compliance
    • EMC Directive
    • Low Voltage Directive
  • Determining Power Requirements
  • Choosing a Module Slot in a Local I/O Chassis
    • Installation considerations
  • Installing the Module
    • Removing the terminal block
  • Wiring the Module
    • Cold Junction Compensation (CJC)
    • Wiring considerations
    • Preparing and Wiring the Cables
    • Specifications
  • Chapter 3
• 3 - Configuring the Module
  • Loop Operation Mode
    • Word 1, Bits 0 and 1 for Channel 1
  • Type of Loop Input
    • Word 1, Bits 2-5 for Channel 1
  • Enable Loop Alarms
    • Word 1, Bit 6 for Channel 1
  • TC Break Response
    • Word 1, Bits 7 and 8 for Channel 1
  • Loop Autotune Gains Level
    • Word 1, Bits 10 and 11 for Channel 1
  • Barrel/Non-barrel Control
    • Word 1, Bit 12 for Channel 1
    • Barrel Control
    • Non–barrel control
    • Switching the barrel control
  • Inner/Outer Zone Selection
    • Word 1, Bit 13 for Channel 1
  • High/Low CV Limits
    • Words 2 and 3 for Channel 1
  • TC Break Control
    • Word 4 or O:e.8 for Channel1
  • Standby Setpoint
    • Word 5 for Channel 1
  • Heat/Cool Minimum On-times
    • Words 6 and 8 for channel 1
  • Heat/Cool TPO Period
    • Words 7 and 9 for Channel 1
  • PV Rate and Associated Alarm
    • Word 10 and Alarm Bit I:e.4/05 for Channel 1
  • High/Low Temperature and Deviation Alarms
    • Words 11-14 for Channel 1
  • Alarm Dead Band
    • Word 15 for Channel 1
  • Thermal Integrity Loss Detection
    • Words 16 and 17 for Channel 1
  • Ramp Rates
    • Words 18 for Channel 1
  • Non-barrel Autotune Disturbance Size
    • Word 20 for Channel 1
    • Implied Decimal Point
  • Configuration Block, M1 File, Loops 1-4 N10:0-100
  • Startup Aggressiveness factor
  • Ramp Rates
  • Chapter 4
• 4 - Setting Autotune and Gains Values
  • Sequence of Setting PID Gains
  • Autotuning the Loops
  • Fine-Tuning the Loops
  • Using the PID Equation
  • Entering Autotune/Gains Values with Implied Decimal Point
    • PID Gains/Autotune Block, M0 File for Loops 1–4
  • Chapter 5
• 5 - Control and Autotune a Loop
  • Controlling a Loop
    • M1 Configuration File
    • Output Image Table
  • Autotune a Loop
    • Requirements for Autotune
    • Items to check before autotune
    • Autotune barrel control applications
    • Example: Autotune non–barrel control applications
    • Troubleshooting Autotune
  • Using the Output Image Table
    • Global Commands to All Loops
  • BTM Auto Tune
  • Chapter 6
• 6 - Monitoring Status Data
  • Input Image Table
    • Implied Decimal Point
  • Chapter 7
• 7 - Calibrating the Module
  • About the Procedure
    • Calibration Codes and Status
    • Calibration Procedure
  • Chapter 8
• 8 - Troubleshooting the Module
  • Troubleshooting with LED Indicators
  • Locating Error Code Information
  • Chapter 9
• 9 - Sample Program
  • Obtaining the Sample Program from the Internet
    • To Access the Internet:
  • RSLogix500 Version
  • BTM Firmware Revision
  • Support for 5/03, 5/04, 5/04P, 5/05, and 5/05P Processors Using BTM201.rss
    • BTM201.rss Data Table Layout
    • Download and Upload Settings
    • BTM201.rss Programming Notes
  • Support for 5/02 Processors Using BTM50220.RSS
    • BTM50220.RSS Data table layout
    • Download and Upload Settings
  • General Notes for Programming the 1746-BTM
• Index
  • A
  • C
  • D
  • F
  • G
  • H
  • I
  • M
  • O
  • P
  • R
  • S
  • T
• Back Cover