Document Outline

• 1732E-UM005A-EN-E 1732E ArmorBlock Dual-Port EtherNet/IP 4-PointAnalog Input and Output Modules User Manual
  • Preface
    • Who Should Use this Manual
    • Purpose of this Manual
      • Related Documentation
    • Common Techniques Used in this Manual
  • 1 – Overview of the 1732E ArmorBlock Analog Input and Output Modules
    • Overview
    • Module Features
    • Physical Features of Your Modules
    • Types of Modules
    • Hardware/Software Compatibility
    • Input and Output Types
    • Alarms/Limits
      • Process Alarms
      • Clamping
      • Overrange and Underrange Detection
    • Digital Filters
    • Chapter Summary
  • 2 – Install Your ArmorBlock Module
    • Overview
    • Install the Module
      • Set the Network Address
        • Network Address Switch value 001
        • Default Factory Configuration
    • Mount the Module
      • Mount the Module in High Vibration Areas
    • Wire the Module
      • I/O Connectors
      • Ethernet Connector
      • Power Connectors
    • Chapter Summary
  • 3 – Configure Your Analog Input and Output Modules with RSLogix 5000 Software
    • Introduction
    • Set Up the Hardware
    • Create the Example Application
    • Configure Your I/O Module
      • RSLogix 5000 Configuration Software
    • Overview of the Configuration Process through RSLogix 5000
    • Add a New Bridge and Module to Your RSLogix 5000 Project
      • Add the Local EtherNet/IP Bridge to the I/O Configuration
      • Add the I/O module as a child of the 1756-EN2T module
    • Download the Program to Your Controller
    • Edit Your 1732E-IF4M12R Configuration
      • General Tab
      • Connection Tab
      • Configuration Tab
      • Alarm Configuration Tab
      • Internet Protocol Tab
      • Calibration Tab
    • Edit Your 1732E-OF4M12R Configuration
      • General Tab
      • Connection Tab
      • Configuration Tab
      • Limits Configuration Tab
      • Fault/Program Action Tab
      • Internet Protocol Tab
      • Calibration Tab
    • Status and Monitoring Tabs
    • Chapter Summary
  • 4 – Configurable Features for the Analog Input and Output Modules
    • Overview
    • Configurable Features for the 1732E-IF4M12R Input Module
      • Input Types and Ranges
        • Current Mode
        • Voltage Mode
      • Digital Filters
      • High Engineering/Low Engineering
      • Real-time Sampling
      • Process Alarms
    • Configurable Features for the 1732E-OF4M12R Output Module
      • Output Types and Ranges
        • Current Mode
        • Voltage Mode
      • High Engineering/Low Engineering
      • Fault Mode and Program Mode
      • Clamping/Limiting
        • Clamp/Limit Alarms
    • Data Tables
    • Chapter Summary
  • 5 – Calibrate Your Modules
    • Overview
    • Difference of Calibrating an Input Module and an Output Module
      • Calibrate in Program or Run Mode
    • Calibrate the Input Module (1732E-IF4M12R)
    • Calibrate the Output Module (1732E-OF4M12R)
      • Current Meter Calibrations
      • Voltage Meter Calibrations
    • Chapter Summary
  • 6 – Troubleshoot the Modules
    • Interpret Status Indicators
    • Check for Faults
  • A – Specifications
    • General Specifications
    • Input Specifications
    • Output Specifications
    • Environmental Specifications
    • Certifications
  • B – 1732E ArmorBlock Embedded Web Server
    • Introduction
    • Typical Applications
    • Browser Requirements
    • Access the Home Page of the Web Server
    • Log On to the Web Server
    • Navigate the 1732E ArmorBlock I/O
    • Access Diagnostic Information
    • Access Configuration Information
  • C – Module Tag Definitions
    • Module Tags for 1732E-IF4M12R
    • Module Tags for 1732E-OF4M12R
    • Access the Module Tags
  • Index
• Back Cover