Hardy HI 200DNWM DeviceNet Weigh Module - Manual (Page 4)

HI 200DNWM MANUAL
ii
CHAPTER 3 - INSTALLATION - - - - - - - - - - - - - - - - -3-1
SCOPE - - - - - - - - - - - - - - - - - - - - - - - - - - - -3-1
Unpacking - - - - - - - - - - - - - - - - - - - - - - - - - - -3-1
Mechanical Installation - - - - - - - - - - - - - - - - - - - - -3-3
Installing the Bare Weigh Module in an Enclosure - - - - - -3-3
Installing Weigh Module in DIN Rail - - - - - - - - - - - - -3-5
Installing the Pre-stacked Weigh Module - - - - - - - - - -3-9
Electrical Installation - - - - - - - - - - - - - - - - - - - - - -3-10
Wiring Diagram for the J1 Load Sensor 8 Pin Connector - -3-10
Wiring Diagram for the J2 DeviceNet Interface 5 Pin Open -3-11
Wiring Diagram for the J3 Set Point Out 4 Pin - - - - - - - -3-11
Wiring Diagram for the HI 215JB Junction Box - - - - - - -3-11
C2 Loadcell Cable Connection (J1) - - - - - - - - - - -3-11
Non-C2 Loadcell Cable Connection (J1) - - - - - - - -3-13
CHAPTER 4 - CONFIGURATION - - - - - - - - - - - - - - -4-1
SCOPE - - - - - - - - - - - - - - - - - - - - - - - - - - - -4-1
Differences in the Series A and Series B Modules - - - - - - - -4-1
Changing from the Series A to the Series B Module - - - - -4-1
Changing from the Series B to the Series A Module - - - - -4-1
DIP Switch (S1) Configuration - - - - - - - - - - - - - - - - -4-2
DIP Switch Location - - - - - - - - - - - - - - - - - - - -4-2
Configuring the Baud Rate - - - - - - - - - - - - - - - - -4-2
Configuring the DeviceNet Node Address - - - - - - - - - -4-3
CHAPTER 5 - SETUP - - - - - - - - - - - - - - - - - - - - -5-1
SCOPE - - - - - - - - - - - - - - - - - - - - - - - - - - - -5-1
Saving to Non-Volatile Ram - - - - - - - - - - - - - - - - - -5-1
Parameters - - - - - - - - - - - - - - - - - - - - - - - - - -5-2
Command Interface - - - - - - - - - - - - - - - - - - - -5-7
Format of Commands (4 byte input data) - - - - - - - -5-8
Examples Using the Command Interface - - - - - - - -5-9
Setpoints - - - - - - - - - - - - - - - - - - - - - - - - - - -5-10
About SetPoints - - - - - - - - - - - - - - - - - - - - - -5-10
Dead Band Limits - - - - - - - - - - - - - - - - - - - - -5-10
Three General Rules for Set Points - - - - - - - - - - - - -5-11
Preact Limits - - - - - - - - - - - - - - - - - - - - - - - -5-11
Entering Set Points - - - - - - - - - - - - - - - - - - - - -5-11
Setpoint Mode Parameters - - - - - - - - - - - - - - - - -5-12
About Setpoint Mode Parameter - - - - - - - - - - - -5-12
Entering Setpoint Mode Parameters - - - - - - - - - -5-12