Comtrol AT Command Set Rev A - Manual (Page 225)

Index
#
#UD – Last Call Status Report ....................................... 3-78
$
$F – FastConnect Control .............................................. 3-88
%
%7 - Plug and Play Serial Number ................................. 3-12
%8 - Plug and Play Vendor ID and Product Number ...... 3-13
%C - Enable/Disable Data Compression........................ 3-71
%E - Enable/Disable Line Quality Monitor ...................... 3-55
%L - Report Line Signal Level........................................ 3-43
%Q - Report Line Signal Quality..................................... 3-43
%U - Select µ-Law or A-Law Codec Type ...................... 3-56
&
&C - RLSD (DCD) Option............................................... 3-23
&D - DTR Option............................................................ 3-23
&F - Restore Factory Configuration................................ 3-10
&G - Select Guard Tone................................................. 3-39
&K - Flow Control........................................................... 3-24
&L - Leased Line Operation ........................................... 3-86
&M - Asynchronous/Synchronous Mode Selection ......... 3-25
&P - Select Pulse Dial Make/Break Ratio ....................... 3-39
&Q - Sync/Async Mode .................................................. 3-26
&R - RTS/CTS Option .................................................... 3-27
&S - DSR Override......................................................... 3-27
&T - Local Analog Loopback Test .................................. 3-10
&V - Display Current Configuration ................................ 3-40
&V1 - Display Last Connection Statistics........................ 3-41
&W - Store Current Configuration................................... 3-11
&X - Select Synchronous Clock Source ......................... 3-28
&Y - Designate a Default Reset Profile........................... 3-11
&Zn=x - Store Telephone Number.................................. 3-12
)
)M - Enable Cellular Power Level Adjustment ................ 3-86
*
**- Load Flash Memory .................................................. 3-14
*B - Display Blacklisted Numbers ................................... 3-43
*D - Display Delayed Numbers....................................... 3-44
:
:E - Compromise Equalizer Enable Command ............... 3-87
@
@M - Initial Cellular Power Level Setting ....................... 3-87
^
^C2 - Download Cellular Phone Driver ......................... 3-113
^I - Identify Cellular Phone Driver ................................. 3-114
^T6 - Indicate Status of Cellular Phone.........................3-114
+
+A8E - V.8 and V.8bis Operation Controls......................3-72
+A8I: - CI Signal Indication .............................................3-73
+DR - Data Compression Reporting ...............................3-69
+DS - Data Compression................................................3-67
+DS44 - V.44 Compression Select .................................3-68
+EB - Break Handling in Error Control Operation............3-59
+EFCS - 32-bit Frame Check Sequence.........................3-60
+ER - Error Control Reporting ........................................3-61
+ES - Error Control and Sync Mode Selection ................3-57
+ESA - Configure Synchronous Access Submode..........3-74
+ESR - Selective Repeat................................................3-59
+ETBM - Call Termination Buffer Management...............3-63
+FAA - Answer Parameter..............................................5-22
+FAA - Auto Answer Enable .............................................4-6
+FAE - Auto Answer Enable .............................................4-7
+FAR - Adaptive Reception Control................................4-13
+FAXERR - T.30 Session Error Report...........................5-21
+FBOR - Data Bit Order .................................................5-22
+FBUF? - Buffer Size .....................................................5-23
+FCFR - Indicate Confirmation to Receive......................5-15
+FCIG - Set Polling ID ....................................................5-13
+FCIG: - Report the Polled Station ID.............................5-17
+FCL - Carrier Loss Timeout ..........................................4-14
+FCLASS- Select Active Service Class ............................3-2
+FCLASS=1 - Select Facsimile Class 1 Mode ..................4-6
+FCLASS=1.0 - Select Facsimile Class 1.0 Mode ............4-6
+FCLASS=2 - Select Facsimile Class 2 Mode ..................5-2
+FCLASS=8 - Select Voice Mode.....................................6-4
+FCON - Facsimile Connection Response .....................5-15
+FCQ - Copy Quality Checking.......................................5-21
+FCR - Capability to Receive .........................................5-20
+FCSI: - Report the Called Station ID .............................5-16
+FDCC - DCE Capabilities Parameters ..........................5-18
+FDCS - Current Session Results Parameters ...............5-19
+FDCS: - Report Current Session Capabilities ...............5-15
+FDD - Double Escape Character Replacement.............4-15
+FDIS - Current Sessions Capabilities Parameters ........5-19
+FDIS: - Report Remote Station Capabilities..................5-15
+FDR - Begin or Continue Phase C Receive Data..........5-11
+FDT - Data Transmission................................................5-7
+FDTC: - Report the Polled Station Capabilities .............5-17
+FET - Transmit Page Punctuation.................................5-10
+FET: - Post Page Message Response..........................5-16
+FHNG: - Call Termination with Status ...........................5-17
+FIT - DTE Inactivity Timeout .........................................4-16
+FK - Session Termination .............................................5-13
+FLID= - Local ID String .................................................5-20
+FLO - Flow Control .......................................................4-19
+FLPL - Indicate a Document for Polling ........................5-13
+FMDL? - Identify Product Model .....................................5-5
+FMFR? - Request Manufacturer Identification.................5-5
+FMI? - Request Manufacturer Identification ..................4-18
+FMM? - Request Model Identification ...........................4-18
+FMR? - Request Revision Identification........................4-18
+FPHCTO - DTE Phase C Response Time-out ..............5-21