Comtrol AT Command Set Rev A User Manual
Page 226
+FPOLL - Indicate Polling Request ................................ 5-17
+FPR - Fixed DTE Rate ................................................. 4-17
+FPTS: - Receive Page Transfer Status ........................ 5-16
+FPTS: - Transmit Page Transfer Status ....................... 5-16
+FPTS= - Page Transfer Status ..................................... 5-21
+FREV? - Identify Product Revision ................................. 5-6
+FRH - Receive Data with HDLC Framing ..................... 4-12
+FRM - Receive Data .................................................... 4-10
+FRS - Receive Silence ................................................... 4-8
+FSPL - Enable Polling .................................................. 5-13
+FTH - Transmit Data with HDLC Framing..................... 4-11
+FTM - Transmit Facsimile............................................... 4-9
+FTS - Transmit Silence .................................................. 4-7
+FTSI: - Report the Transmit Station ID ......................... 5-15
+GCAP - Request Complete Capabilities List................... 3-8
+GCI - Country of Installation ........................................... 3-9
+GMI - Request Conexant Identification........................... 3-7
+GMI - Request Manufacturer Identification ..................... 3-7
+GMM - Request Model Identification .............................. 3-8
+GMR - Request Revision Identification........................... 3-8
+H - Enable/Disable RPI and DTE Speed ...................... 3-76
+IFC - DTE-Modem Local Flow Control.......................... 3-30
+ILRR - DTE-Modem Local Rate Reporting ................... 3-31
+IPR - Fixed DTE Rate .................................................. 3-29
+ITF - Transmit Flow Control Thresholds ....................... 3-77
+MR - Modulation Reporting Control .............................. 3-53
+MS - Modulation Selection ........................................... 3-51
+PCW - Call Waiting Enable .......................................... 3-89
+PIG - PCM Upstream Ignore ........................................ 3-93
+PMH - Modem-on-Hold Enable .................................... 3-90
+PMHF - V.92 Modem-on-Hold Hook Flash ................... 3-93
+PMHR - Initiate Modem-on-Hold .................................. 3-92
+PMHT – Modem-on-Hold Timer ................................... 3-91
+PQC - V.92 Phase 1 and Phase 2 Control.................... 3-94
+PSS - Use Short Sequence.......................................... 3-95
+VCID - Caller ID (CID).................................................... 3-3
+VDR - Distinctive Ring.................................................. 6-19
+VDT - Control Tone Cadence Reporting....................... 6-20
+VDX - Speakerphone Duplex Mode.............................. 6-23
+VGM - Microphone Gain .............................................. 6-24
+VGR - Voice Gain Receive (Record Gain)...................... 6-8
+VGS - Speaker Gain .................................................... 6-25
+VGT - Voice Gain Transmit (Playback Volume).............. 6-9
+VIP - Voice Initialize All Parameters ............................... 6-5
+VIT - Voice Inactivity Timer (DTE/Modem) ................... 6-10
+VLS - Analog Source/Destination Selection.................. 6-11
+VNH - Automatic Hang-up Control ................................. 6-4
+VPR - Select DTE/Modem Interface Rate .................... 6-21
+VRA - Ringback Goes Away Timer .............................. 6-14
+VRID - Caller ID (CID).................................................... 3-4
+VRN - Ringback Never Appeared Timer....................... 6-15
+VRX - Start Modem Receive (Record)............................ 6-5
+VSD - Silence Detection (Quiet and Silence)................ 6-16
+VSM - Compression Method Selection......................... 6-17
+VSP - Speakerphone ON/OFF ..................................... 6-22
+VTD - Beep Tone Duration Timer................................. 6-18
+VTS - Send Voice Tone(s) ............................................. 6-6
+VTX - Start Modem Transmit (Playback) ........................ 6-8
A
A - Answer ..................................................................... 3-35
B
B - CCITT or Bell............................................................ 3-56
\B - Transmit Break to Remote ....................................... 3-64
D
D - Dial3-32
E
E - Command Echo ........................................................3-16
H
H - Disconnect (Hang-Up) ..............................................3-36
I
I - Identification .................................................................3-6
K
\K - Break Control...........................................................3-65
-K - MNP Extended Services ..........................................3-66
L
L - Speaker Volume........................................................3-38
M
M - Speaker Control .......................................................3-38
N
\N - Operating Mode .........................................................3-5
O
O - Return to On-Line Data Mode ...................................3-37
P
P - Set Pulse Dial Default ...............................................3-35
–PPD= - Extension Pickup Notification ...........................3-44
Q
Q - Quiet Results Codes Control ....................................3-16
-QCPC - Force Full Startup Procedure Next Connection 3-96
-QCPS - Enable Quick Connect Profile Save..................3-96
S
S - Read/Write S-Parameter ...........................................3-97
S0 - Number of Rings to Auto-Answer ............................3-99
S1 - Ring Counter...........................................................3-99
S10 - Lost Carrier To Hang Up Delay ...........................3-101
S11 - DTMF Tone Duration ..........................................3-101
S12 - Escape Prompt Delay (EPD) ...............................3-102
S14 - General Bit Mapped Options Status ....................3-102
S16 - Test Mode Bit Mapped Options Status ................3-102
S19 - Reserved ............................................................3-103
S2 - Escape Character ...................................................3-99
S20 - Reserved ............................................................3-103
S21 - V.24/General Bit Mapped Options Status ............3-103
S210 – V.34 Symbol Rates...........................................3-112
S22 - Speaker/Results Bit Mapped Options Status .......3-104
S23 - General Bit Mapped Options Status ....................3-104
S24 - Sleep Inactivity Timer..........................................3-104
S25 - Delay To DTR Off................................................3-105
S26 - RTS to CTS Delay...............................................3-105
S27 - Bit Mapped Options Status..................................3-105
S28 - Bit Mapped Options Status..................................3-106
S29 - Flash Dial Modifier Time......................................3-106
S3 - Carriage Return Character ......................................3-99
S30 - Disconnect Inactivity Timer..................................3-106
S31 - Bit Mapped Options Status..................................3-107
S36 - LAPM Failure Control..........................................3-107
S38 - Delay Before Forced Hang Up ............................3-108
S39 - Flow Control Bit Mapped Options Status .............3-108
S4 - Line Feed Character ...............................................3-99