ADLINK PCI-8102 User Manual
User’s manual, Advance technologies; automate the world
Advertising
Table of contents
Document Outline
- Revision History
- Table of Contents
- List of Figures
- Preface
- 1 Introduction
- 2 Installation
- 2.1 Package Contents
- 2.2 PCI-8102 Outline Drawing
- 2.3 PCI-8102 Hardware Installation
- 2.4 Software Driver Installation
- 2.5 P1 Pin Assignments: Main connector
- 2.6 P2 Pin Assignment: Digital Inputs / Outputs
- 2.7 K1/K2 Pin Assignments: Simultaneous Start/ Stop
- 2.8 Jumper Settings for Pulse Output
- 2.9 CMP & EMG Interface Settings
- 2.10 Switch Setting for card index
- 3 Signal Connections
- 3.1 Pulse Output Signals OUT and DIR
- 3.2 Encoder Feedback Signals EA, EB and EZ
- 3.3 EMG Emergency Stop
- 3.4 Origin Signal ORG
- 3.5 End-Limit Signals PEL and MEL
- 3.6 In-Position Signal INP
- 3.7 Alarm Signal ALM
- 3.8 Deviation Counter Clear Signal ERC
- 3.9 General-Purpose Signal SVON
- 3.10 General-Purpose Signal RDY
- 3.11 Position Compare Output pin: CMP
- 3.12 Multi-Functional Input Pin: LTC/SD/PCS/CLR
- 3.13 Simultaneously Start/Stop Signals STA and STP
- 3.14 General Purpose Digital Input/Output
- 4 Operations
- 4.1 Classifications of Motion Controller
- 4.1.1 Voltage Type Motion Control Interface
- 4.1.2 Pulse Type Motion Control Interface
- 4.1.3 Network Type Motion Control Interface
- 4.1.4 Software Real-time Motion Control Kernel
- 4.1.5 DSP Based Motion Control Kernel
- 4.1.6 ASIC Based Motion Control Kernel
- 4.1.7 Compare Table of All Motion Control Types
- 4.1.8 PCI-8102’s Motion Controller Type
- 4.2 Motion Control Modes
- 4.2.1 Coordinate System
- 4.2.2 Absolute and Relative Position Move
- 4.2.3 Trapezoidal Speed Profile
- 4.2.4 S-Curve and Bell-Curve Speed Profile
- 4.2.5 Velocity Mode
- 4.2.6 One Axis Position Mode
- 4.2.7 Two Axes Linear Interpolation Position Mode
- 4.2.8 Two Axes Circular Interpolation Mode
- 4.2.9 Continuous Motion
- 4.2.10 Home Return Mode
- 4.2.11 Home Search Function
- 4.2.12 Manual Pulser Function
- 4.2.13 Simultaneous Start Function
- 4.2.14 Speed Override Function
- 4.2.15 Position Override Function
- 4.3 Motor Driver Interface
- 4.4 Mechanical Switch Interface
- 4.5 Counters
- 4.6 Comparators
- 4.7 Other Motion Functions
- 4.8 Interrupt Control
- 4.9 Multiple Card Operation
- 4.1 Classifications of Motion Controller
- 5 MotionCreatorPro
- 6 Function Library
- 6.1 List of Functions
- 6.2 C/C++ Programming Library
- 6.3 Initialization
- 6.4 Pulse Input/Output Configuration
- 6.5 Velocity mode motion
- 6.6 Single Axis Position Mode
- 6.7 Linear Interpolated Motion
- 6.8 Circular Interpolation Motion
- 6.9 Home Return Mode
- 6.10 Manual Pulser Motion
- 6.11 Motion Status
- 6.12 Motion Interface I/O
- 6.13 Interrupt Control
- 6.14 Position Control and Counters
- 6.15 Position Compare and Latch
- 6.16 Continuous Motion
- 6.17 Multiple Axes Simultaneous Operation
- 6.18 General-Purposed DIO
- 6.19 Soft Limit
- 6.20 Backlash Compensation / Vibration Suppression
- 6.21 Speed Profile Calculation
- 6.22 Return Code
- 7 Connection Example
- Appendix
- Important Safety Instructions
- Getting Service