ONICON System-10 P1 User Manual

Page 34

Advertising
background image

11451 Belcher Road South, Largo, FL 33773 • USA • Tel +1 (727) 447-6140 • Fax +1 (727) 442-5699 • [email protected]

System-10-P1 Manual 10/14 - 0656-9 / 18320

Page 34

P1 POINTS

Pt

Name/Range

Type

Category

COV

OVR

Default

Initial

Current

1

Address Range: 1-99

02

LAO

NO

YES

99

11

H

None

2

Application

02

LAO

NO

NO

1999

10

1999

10

None

3

Energy Rate - 0-32,767

03

LAI

YES

NO

0

0

Integer

4

Flow Rate - 0-32,767

03

LAI

YES

NO

0

0

Integer

5

Supply Temperature - 0-250°F

03

LAI

YES

NO

0

0

Integer

6

Return Temperature - 0-250°F

03

LAI

YES

NO

0

0

Integer

7

Delta Temperature - 0-250°F

03

LAI

YES

NO

0

0

Integer

8

Operating Mode: 1/Heat, 2/Cool

03

LDI

NO

NO

0

0

Byte

9

W0-M1 Energy: 000,000-009,999

03

LAI

NO

NO

0

0

Integer

10

W1-M1 Energy: 010,000-999,999

03

LAI

NO

NO

0

0

Integer

11

W0-M1Volume: 000,000-009,999

03

LAI

NO

NO

0

0

Integer

12

W1-M1 Volume: 010,000-999,999

03

LAI

NO

NO

0

0

Integer

13

W0-M2 Energy: 000,000-009,999

03

LAI

NO

NO

0

0

Integer

14

W1-M2 Energy: 010,000-999,999

03

LAI

NO

NO

0

0

Integer

15

W0-M2 Volume: 000,000-009,999

03

LAI

NO

NO

0

0

Integer

16

W1-M2 Volume: 010,000-999,999

03

LAI

NO

NO

0

0

Integer

17

W0-AuxiIn-1: 000,000-009,999 (Di3)

03

LAI

NO

NO

0

0

Integer

18

W1-AuxiIn-2: 010,000-999,999 (Di3)

03

LAI

NO

NO

0

0

Integer

19

Not Used

20

Point 20, Override Time (Hours)

Range 0-FF

02

LAO

NO

YES

1

1

None

21

M-1 E Reset - 0/Off, 1/Reset

01

LDO

NO

YES

0

0

Byte

22

M-1 V Reset - 0/Off, 1/Reset

01

LDO

NO

YES

0

0

Byte

23

M-2 E Reset - 0/Off, 1/Reset

01

LDO

NO

YES

0

0

Byte

24

M-2 V Reset - 0/Off, 1/Reset

01

LDO

NO

YES

0

0

Byte

25

AuxIn Reset - 0/Off, 1/Reset (Di3)

01

LDO

NO

YES

0

0

Byte

29

DAY.NGT

ON=Night; OFF=Day; Default=OFF

01

LDO

NO

YES

0

0

Byte

99

ERROR STATUS Bit Oriented

01

LAO

NO

YES

0

0

Integer

100

Point 100

Factory Flag

Factory Flag is not a point in the sense that the others are. It is referenced only by

the Memorize Point Command. Other commands should NAK it with “POINT DOES

NOT EXIST”.

NOTE: Also refer to the Siemens’ Application Note, Document No. 140-0280 for additional information.

Advertising