Brocade Unified IP MIB Reference (Supporting FastIron Releases 07.5.00 and 08.0.10) - Manual (Page 610)

584 Unified IP MIB Reference
53-1003106-01
LAG group table
59
fdryLinkAggregationGroupAdminStatus
brcdIp.1.1.3.33.1.1.1.3
Syntax: Integer Read-create Displays the desired deployed state of this LAG entry.
NOTE: This is not the operational status. Refer to ifTable
for the operational status.
•
deploy(1)—Deploy the LAG and set to LACP active if
a dynamic LAG.
•
deployPassive(2)—Deploy the LAG and set to LACP
passive if a dynamic LAG.
•
undeploy(3)—Undeploy the LAG if no more than two
ports are enabled.
•
undeployForced(4)—Undeploy the LAG regardless of
the number of ports enabled.
NOTE: undeployForced(4) status is a write-only value. In
particular, a row cannot be deployed until the
corresponding instances of
fdryLinkAggregationGroupIfList have been set.
fdryLinkAggregationGroupIfList
brcdIp.1.1.3.33.1.1.1.4
Syntax: OCTET STRING Read-create Displays a list of interface indices which are the port
memberships of a trunk group. Each interface index is a
32-bit integer in big-endian order.
NOTE: This object accepts a 32-bit integer only.
fdryLinkAggregationGroupPrimaryPort
brcdIp.1.1.3.33.1.1.1.5
Syntax: InterfaceIndexOrZero Read-create Displays the primary port for the Link Aggregation Group.
This must be set before deploying the Link Aggregation
Group unless this is a keepalive Link Aggregation Group.
fdryLinkAggregationGroupTrunkType
brcdIp.1.1.3.33.1.1.1.6
Syntax: Integer Read-create Displays the trunk connection type, which specifies the
scheme of load-sharing among the trunk ports.
fdryLinkAggregationGroupTrunkThresh
old
brcdIp.1.1.3.33.1.1.1.7
Syntax: Unsigned32 Read-create DIsplays the number of up ports needed to keep the
trunk up.
NOTE: This object is not applicable to keepalive LAGs.
fdryLinkAggregationGroupLacpTimeout
brcdIp.1.1.3.33.1.1.1.8
Syntax: Integer Read-create Displays the LACP timeout value this LACP LAG will use.
Applicable for dynamic and keepalive LAGs only.
fdryLinkAggregationGroupIfIndex
brcdIp.1.1.3.29.2.1.1.9
Syntax: InterfaceIndex Read-only After a LAG is deployed, this object dIsplays information
for the LAG entry in the ifTable. Use the variabe to access
the entry in the ifTable and ifXTable. Zero(0) is returned
for LAGs that have not been deployed.
fdryLinkAggregationGroupPortCount
brcdIp.1.1.3.33.1.1.1.10
Syntax: Unsigned32 Read-only Displays the number of member ports that belong to this
LAG.
fdryLinkAggregationGroupRowStatus
brcdIp.1.1.3.33.1.1.1.11
Syntax: RowStatus Read-create Displays the status of this conceptual row.
createAndWait(5) is not supported.
To create a row in this table, a manager must set this
object to createAndGo(4) together with the setting of
fdryLinkAggregationGroupType. After that, the row status
becomes active(1) regardless of whether or not the LAG
entry is deployed.
To deploy the LAG entry, set the corresponding instance
of fdryLinkAggregationGroupAdminStatus to deployActive
or deployPassive.
Name, OID, and syntax Access Description