GW Instek PSB-2000 Series User Manual User Manual

GW Instek Equipment

Advertising

Muti-Range Bench-Top DC Power
Supply

PSB-2000 series

User Manual

GW INSTEK PART NO. 82SB-28H00E01

ISO-9001 CERTIFIED MANUFACTURER

Advertising

Table of contents

Document Outline

SAFETY INSTRUCTIONS
- Safety Symbols
- Safety Guidelines
- Power cord for the United Kingdom
GETTING STARTED
- PSB 2000 Series Overview
  - Series line up
  - Main Features
  - Accessories
  - Standard Accessories
- Appearance
  - Front Panel (PSB-2400L2 shown)
  - Front Panel (PSB-2400H shown)
  - Panel Operation Unit
  - Rear Panel (PSB-2400L2 shown)
  - Pin assignment of the J3 External Control Connector (PSB-2400L, 2800L, 2400L2, 2800LS)
  - Pin assignment of J3 external control connector (PSB-2400H, 2800H)
OPERATION
- Connecting the AC Power Cable
- Connecting the Load to the Output Terminals
  - Connecting to the Rear Output Terminals (PSB-2400L, 2800L, 2400L2, 2800LS)
  - Connection with the Rear Output Terminals (PSB-2400H, 2800H)
  - Connection with the Front Output Terminals (PSB-2400L, 2800L, 2400L2, 2800LS)
  - Assembling and Connecting the Front Output Terminal Plugs (PSB-2400H, 2800H)
- Operation Ranges (PSB-2400L, 2800L, 2400L2, 2800LS)
- Operation Ranges (PSB-2400H, 2800H)
- Various Settings
  - Turning the Power On
  - How to Set the Voltage
  - How to Set the Current
  - How to Set Power
  - How to Turn the Output On
  - How to Display the Setting Value When the Output is On
  - How to Rotate the Display Panel 90 Degrees for Vertical Installation
  - How to Disable Panel Operations (Key Lock Function)
- Menu Key Functions
  - Preset Function
  - OVP/OCP function
  - Hi-Ω- Function
  - Off Timer Function
  - Sequence Function
  - External Control (External Voltage, External Resistance)
  - External Control Output On/Off
  - Delay Function
  - Tracking Function
  - Master-slave function
- Voltage Sense
- External Control Functions
  - Assembling the XG5M-2635-N Connector
  - Output Voltage Monitor and Output Current Monitor
  - Constant-Voltage (CV) Control with External Voltage or Resistance
  - Constant-Current (CC) Control with External Voltage or Resistance
  - Output ON/OFF with External Contacts
  - Alarm Function using External Contacts
  - Status Signals (CV, CC & ALARM)
- Using the Sequence Function
OTHER FUNCTIONS
- Power Extension using PSB-2800LS (Parallel Connection Only)
  - How to use the PSB-2800LS
- Using the PSB-007 Extension kits
  - How to Connect the Units Vertically
  - How to Connect the Units Horizontally
  - Bus Bar Connection
EXTERNAL CONTROL
- Remote Control
- Interface Connectors
- PSB-001 Specifications (optional)
- PSB-002 Specifications (standard)
- Connection Methods
- Connection Cables
- Address Setting
- Using the Interface Boards
  - Using the GPIB interface
  - Using the USB interface
  - Using the RS-232C Interface
  - Using the Local Bus
- Communication Commands
  - Output Voltage Setting (:VOLT)
  - OVP Setting (:VOLT:PROT)
  - Output current setting (:CURR)
  - OCP setting (:CURR:PROT)
  - Output power setting (:POW)
  - OUTPUT ON/OFF (:OUTP)
  - Hi-Ω ON/OFF(:CONF:HIZ)
  - Hi-Ω Time Setting (:CONF:HIZ:HOLD)
  - Display Switching (:CONF:DISP)
  - Tracking ON/OFF (:CONF:TRAC)
  - External Control Setting (:EXT:MOD)
  - External Control of the Voltage Output ON/OFF (:EXT:VOLT)
  - External Control of the Current Output ON/OFF (:EXT:CURR)
  - Output switching (:EXT:OUTP)
  - Off Timer ON/OFF (:TIMER:MOD)
  - Off Timer Value Setting (:TIMER:SET)
  - Delay Function ON/OFF (:DELAY:MOD)
  - Delay Rise Time Setting (:DELAY:RISE)
  - Delay Fall Time Setting (:DELAY:FALL)
  - Monitor Inquiry (:MEAS?)
  - Preset Recall (:PRES:CALL)
  - Preset Saving (:PRES:SAVE)
  - Sequence Mode Setting (:SEQ:MOD)
  - Sequence Jump Setting (:SEQ:STEP)
  - Sequence Start Step Setting (:SEQ:START)
  - Sequencer End Step Setting (:SEQ:END)
  - Sequence Repetition Frequency Setting (:SEQ:CYCL)
  - Sequence Data Transfer (:SEQ:DOWNLOAD)
  - Model Inquiry (*IDN?)
  - Standard Event Status Register Inquiry (*ESR?)
  - Standard Event Status Enable Register Setting (*ESE)
  - Status Byte Inquiry (*STB?)
  - SRQ (Service Request)Register Setting (*SRE)
  - Buffer Clear (*CLS)
  - Communication Reset (*RST)
  - Command Completion (*OPC)
  - Wait for Completion (*WAI)
  - Local Address Setting (:ADDR)
  - Remote/Local Setting (:REMOTE)
- Registers
  - Status Byte Register (STB, SRE)
  - Standard Event Register (ESR, ESE)
  - Function of the Status Byte Register
  - Reading Data from the Status Byte Register and Clearing the Status Byte Register
  - Clear and Reset Statuses
  - Remote/Local Function
  - Responses to Multi-Line Message Commands
APPENDIX
- Trouble Shooting
- Maintenance
- Dimensions
- Specifications
  - Output
  - Input
  - Constant-Voltage Characteristics
  - Constant-Current Characteristics
  - Constant-Power Characteristics
  - Function
  - Protective functions
  - Others
  - Environmental Conditions
  - Applicable Standards
  - Default Settings and Storage after Power Off
  - Parallel/Serial Operation Setting Table
  - PSB-2400H
  - PSB-2800H
  - PSB-2400L (Part 1/2)
  - PSB-2400L (Part 2/2)
  - PSB-2800L
- Declaration of Conformity