NORD Drivesystems B1000 - Manual (Page 72)

www.nord.com A70
INTRODUCTION
G1000 – Subject to Change Without Notice
Application
Load Duration
Up to
3 hrs
per
day
3-10
hrs
per
day
Over
10 hrs
per
day
METAL STRIP PROCESSING MACHINERY
Bridles
1.25 1.25 1.50
Coilers and uncoilers 1.00 1.00 1.25
Edge Trimmers 1.00 1.25 1.50
Flatteners 1.00 1.25 1.50
Loopers (accumulators) 1.00 1.00 1.00
Pinch rolls 1.00 1.25 1.50
Scrap choppers 1.00 1.25 1.50
Shears 1.50 1.50 1.75
Slitters 1.00 1.25 1.50
MILLS, ROTARY TYPE
BaII & Rod
Spur Ring Gear
1.50 1.50 1.75
HeIicaI Ring Gear 1.50 1.50 1.50
Direct Connected 1.50 1.50 1.75
Cement KiIns 1.50 1.50 1.50
Dryers & CooIers 1.50 1.50 1.50
MIXERS CONCRETE 1.00 1.25 1.50
PAPER MILLS 1)
Agitator (Mixer) 1.50 1.50 1.50
Agitator for Pure Iiquors 1.25 1.25 1.25
Barking Drums 1.75 1.75 1.75
Barkers – MechanicaI 1.75 1.75 1.75
Beater 1.50 1.50 1.50
Breaker Stack 1.25 1.25 1.25
CaIender 2) 1.25 1.25 1.25
Chipper 1.75 1.75 1.75
Chip Feeder 1.50 1.50 1.50
Coating RoIIs 1.25 1.25 1.25
Conveyors
Chip, Bark, ChemicaI
1.25 1.25 1.25
Iog (incIuding SIab) 1.75 1.75 1.75
Couch RoIIs 1.25 1.25 1.25
Cutter 1.75 1.75 1.75
CyIinder MoIds 1.25 1.25 125
Dryers 2)
Paper Machine 1.25 1.25 1.25
Conveyor Type 1.25 1.25 1.25
Embosser 1.25 1.25 1.25
Extruder 1.50 1.50 1.50
Fourdrinier RoIIs (IncIudes Iump
Breaker, Dandy RoII, Wire Turning
and Return RoIIs)
1.25 1.25 1.25
Jordan 1.25 1.25 1.25
KiIn Drive 1.50 1.50 1.50
Mt. Hope RoII 1.25 1.25 1.25
Paper RoIIs 1.25 1.25 1.25
Application
Load Duration
Up to
3 hrs
per
day
3-10
hrs
per
day
Over
10 hrs
per
day
PAPER MILLS (cont)
Presses – FeIt & Suction
1.25 1.25 1.25
PuIper 1.50 1.50 1.75
Pumps – Vacuum 1.50 1.50 1.50
ReeI (Surface Type) 1.25 1.25 1.50
Screens
Chip
1.50 1.50 1.50
Rotary 1.50 1.50 1.50
Vibrating 1.75 1.75 1.75
Size Press 1.25 1.25 1.25
SupercaIendar 3) 1.25 1.25 1.25
Thickener (AC Motor) 1.50 1.50 1.50
Thickener (DC Motor) 1.25 1.25 1.25
Washer (AC Motor) 1.50 1.50 1.50
Washer (DC Motor) 1.25 1.25 1.25
Wind and Unwind Stand 1.00 1.00 1.00
Winders (Surface Type) 1.25 1.25 1.25
Yankee Dryers 2) 1.25 1.25 1.25
PLASTICS INDUSTRY –
PRIMARY PROCESSING
Intensive InternaI Mixers
Batch Mixers
1.75 1.75 1.75
Continuous Mixers 1.50 1.50 1.50
Batch Drop MiII – 2 smooth roIIs
Continuous Feed, HoIding & Biend MiII
1.25 1.25 1.25
CaIendars 1.50 1.50 1.50
PLASTICS INDUSTRY –
SECONDARY PROCESSING
BIow MoIders
1.50 1.50 1.50
Coating 1.25 1.25 1.25
FiIm 1.25 1.25 1.25
Pipe 1.25 1.25 1.25
Pre-PIasticizers 1.50 1.50 1.50
Rods 1.25 1.25 1.25
Sheet 1.25 1.25 1.25
Tubing 1.25 1.25 1.50
PULLERS – BARGE HAUL 1.00 1.50 1.75
PUMPS
CentrifugaI
1.00 1.00 1.25
Proportioning 1.00 1.25 1.50
Reciprocating
SingIe Acting, 3 or more cyIinders
1.00 1.25 1.50
DoubIe Acting, 2 or more cyIinders 1.00 1.25 1.50
Rotary
Gear Type
1.00 1.00 1.50
Lobe 1.00 1.00 1.25
Vane 1.00 1.00 1.25
Engineering
AGMA
Service Factors