Rockwell Automation 2755 2D Hand-Held Scanner User Manual
Bar code programming guide
Advertising
Table of contents
Document Outline
- Front Cover
- Important User Information
- Table of Contents
- Preface - Read this First
- 1 - Scanner Configuration
- Set Default Parameters
- Select The Symbologies You Want to Enable or Disable
- Transmit UPC-A / UPC-E Check Digit
- Convert UPC-E to UPC-A
- Decode UPC / EAN Supplements
- Convert EAN-8 to EAN-13
- Select UPC-A Preamble
- Select UPC-E Preamble
- Select Code 39 - Code Lengths
- Select Codabar Code Lengths
- Select Interleaved 2 of 5 Code Lengths
- Scan 2 Digit Code Length
- Select Prefix/Suffix Options
- Prefix/Suffix - 4 Digit ASCII Equivalent Value
- Data Transmission Format
- Transmit No-Read Message
- Transmit LRC Checksum
- Transmit Code ID Character
- Beeper After Good Decode / Beeper Tone
- Decode Buffering
- Pause Duration
- Decode Attempt Duration
- Pause/Decode Attempt Duration Values
- Smart Raster
- Hand-Held Options
- 2 - RS-232 Synapse Cable (Communication Setup)
- Set RS-232 Synapse Cable Defaults
- RS-232 Synapse Cable Fixed Format Hosts
- RS-232 Synapse Cable Baud Rate
- RS-232 Synapse Cable Parity Options
- RS-232 Synapse Cable Stop and Data Bits
- RS-232 Synapse Cable Hardware Handshaking
- RS-232 Synapse Cable Software Handshaking
- RS-232 Synapse Cable Beep On <BEL>
- RS-232 Synapse Cable Unknown Characters
- RS-232 Synapse Cable Response Timeout
- RS-232 Synapse Cable Advanced Features
- 3 - IBM Keyboard Wedge (Communication Setup)
- 4 - DEC VT520 Keyboard Wedge (Communication Setup)
- 5 - DEC VT220/320/420 Keyboard Wedge Cable (Communication Setup)
- DEC VT220/320/420 Keyboard Wedge Interface Cable Defaults
- DEC VT220/320/420 Keyboard Wedge Synapse Cable Host
- DEC VT220/320/420 Keyboard Wedge Country Selection
- DEC VT220/320/420 Keyboard Wedge Unknown Characters
- DEC VT220/320/420 Keyboard Wedge Intercharacter Delay
- DEC VT220/320/420 Keyboard Wedge Advanced Features
- 6 - Scanner Emulation Cable (Communication Setup)
- Scanner Emulation Synapse Cable Defaults
- Scanner Emulation Host
- Scanner Emulation Variable Leading Margin
- Scanner Emulation Check for Decode LED
- Scanner Emulation Timeout
- Scanner Emulation Polarity
- Send Bar Codes with Unknown Characters
- Scanner Emulation Convert All to Code 39
- Scanner Emulation Code 39 to Code 39 Full ASCII
- Scanner Emulation Cable Advanced Features
- A - ADF Bar Codes
- Special Commands - Start/Save Rules
- Special Commands - Erase/Quit Rules
- Special Commands - Disable Rule Sets
- Criteria - Code Types
- Criteria - Code Lengths
- Criteria - Specific Data String
- Criteria - Numeric Keypad
- Criteria - Specific Data String
- Criteria - Rules Belongs to Sets
- Actions - Send Characters / Data
- Actions - Skip Ahead / Back
- Actions - Spaces and Zeroes
- Actions - Send Value
- Actions - Beeps
- Actions - Pad Spaces
- Actions - Pad Zeros
- Actions - Send Control Characters
- Actions - Send Keyboard Characters
- Actions - AlphaNumeric Keyboard
- Actions - Turn of Rule Set
- B - Enhanced Decoder Application
- C - Flexible Interface Module Application
- D - SLC 5/03, 5/04 Controller Application
- E - PLC-5 Controller Application
- F - DTAM Plus DeviceNet Application
- G - ASCII Chart
- Test Symbols
- Back Cover