Banner A-GAGE MINI-ARRAY Series - Manual (Page 11)

P/N 43298 rev. E
11
Banner Engineering Corp. • Minneapolis, MN U.S.A.
www.bannerengineering.com • Tel: 763.544.3164
MINI-ARRAY ®
Instruction Manual
2.3 Controller Specifications
Specifications
Power Requirements 16 to 30V dc @ 1.25 amps max. (see current requirements for sensors);
Controller alone (without sensors connected) requires 0.1 amp.
Inputs MINI-ARRAY sensor input (5 connections); emitter and receiver wire in parallel to five
terminals.
GATE input: Optically-isolated, requires 10 to 30V dc (7.5K input impedance) for gate signal.
System Response Time Outputs are not active for 5 seconds after system power up. Maximum response time for the
discrete outputs is two scan cycles. A scan cycle includes a sensor scan plus any serial data
transmission.
Serial transmission (if activated) follows every sensor scan.
Discrete Outputs MAC-1: Output 1 (OUT 1): Reed relay contact rated 125V ac/dc max., 10 VA max. resistive
load (non-inductive).
Output 2 (ALARM): Open collector NPN transistor rated 30V dc max., 150 mA max,
short-circuit protected (may be configured as a second data analysis output, system
alarm output, or scan trigger output for a parallel array).
OFF-STATE Leakage Current: <10µA @ 30V dc
ON-STATE Saturation Voltage: <1 Volt @ 10 mA, <1.5 Volt @ 150 mA
MACN-1: (2) Open collector NPN transistor outputs.
MACP-1: (2) Open collector PNP transistor outputs.
Transistor rated 30V dc max., 150 mA max, short circuit protected (may be
configured as a second data analysis output, system alarm output, or scan trigger
output for a parallel array).
OFF-STATE Leakage Current <10µA @30V dc
ON-STATE Saturation Voltage <1 Volt @10 mA, <1.5 Volt @150 mA
MACV-1/MACI-1: Alarm: Open collector NPN transistor rated 30V dc max. 150 mA max, short
circuit protected.
(may be configured as a data analysis output, system alarm output, or scan
trigger output for a parallel array)
OFF-STATE Leakage Current: <10µA @30V dc
ON-STATE Saturation Voltage: <1 Volt @10 mA, <1.5Volt @150 mA
MAC16P-1: Sixteen open collector PNP transistor outputs.
MAC16N-1: Sixteen open collector NPN transistor outputs.
30V dc max,150 mA max., short circuit protected.
OFF-STATE leakage current: <10 µA
ON-STATE Saturation Voltage: <1 Volt @ 10 mA; <1.9V @ 150 mA
Analog Outputs MACV-1: (2) 0-10 Volts sourcing adjustable Null and Span (20 mA current limit).
MACI-1: (2) 4-20 mA current sinking adjustable Null and Span (16 to 30V input).
Resolution: Span minus Null, divided by the number of sensor channels
Linearity: 0.1% of Full Scale
Temp. Var.:
0.01% of Full Scale/°C
Serial Data Outputs All Models: RS-232, ASCII or binary data format.
Baud rate: 9600, 19.2K, or 38.4K 8 data bits, 1 start bit, 1 stop bit, even parity.
Clear data may be suppressed; header string may be suppressed in binary
format.
MAC-1, MACN-1,
and MACP-1: Up to 15 Controllers may be given unique address for RS-485 party line.
Controller Programming Via RS-232 to PC-compatible computer running Windows ® .XP, Vista, or 7
operating system and using Banner-supplied software (see user manual).