Using the system, Utilización del sistema utilisation de la chaine, To select a source – Sony SX-N737 User Manual
Page 10: Para conectar la alimentación, Para seleccionar una fuente, Para escuchar con auriculares, Utilización de la bandeja de control, Para desplegar la etapa de control, Para replegar la bandeja de control, Guía de iluminación o
Attention! The text in this document has been recognized automatically. To view the original document, you can use the "Original mode".
USING THE SYSTEM .........................
UTILIZACIÓN DEL SISTEMA
UTILISATION DE LA CHAINE
FUNCTION
POWER
|lj ;r^
r—--—
---------- ^
____ __________________----------
1
db
\
uw
M
l i@®
PHONES■
V
PLAY/DIR ■
...-L.Fei-'A'va,
^ O®
BAND
STATION PRESET
DSP
OPEN/CLOSE
PLAY/PAUSE
Control stage
Bandeja de control
Pupitre de commande
A
J
Before using the system, set them up as illustrated
on pages 64 through 69.
To turn on the power
Plug in the AC cord and press POWER.
To select a source
After turning on the power, press one of the
FUNCTION select buttons.
The CD or TAPE function is also selected and
playback started by pressing the respective PLAY
buttons. However, if a CD or a tape is not inserted,
playback does not begin.
The TUNER function can also be selected by
pressing BAND, followed by a STATION PRESET
button. The previous station of the last band is
selected.
To listen through headphones
Plug in headphones with a standard 6.3 o plug into
the PHONES jack.
Using the control stage
In addition to the buttons and switches on the main
unit and remote control, there is also a retractable
control panel on the amplifier.
To extend the control stage
Press OPEN/CLOSE to extend the stage. The
stage also opens when DSP is pressed. However,
if no operation is activated after about 8 seconds,
the stage automatically closes.
To close the control stage
Press OPEN/CLOSE again to close the stage, or
lightly push in the stage. The stage retracts into
the amplifier. ,
Illumination guide O
When one of the FUNCTION buttons is pressed,
other buttons light or blink to make the sequence
of steps easy to follow.
Example: Listening to the tuner
When TUNER is pressed, the STATION PRESET
buttons light.
Antes de utilizar el sistema, ajúsfelo como se
indica en las páginas 64 a 69.
Para conectar la alimentación
Enchufe el cable de alimentación de CA y presione
POWER.
Para seleccionar una fuente
Después de haber conectado la alimentación,
presione uno de los botones FUNCTION.
La función del reproductor de discos compactos
(CD) o del deck de casetes (TAPE) también se
seleccionará
y
se
iniciará
la
reproducción
presionando PLAY respectivo. Sin embargo, si no
hay
disco
compacto
o
casete
insertado,
la
reproducción no se iniciará.
La función del sintonizador (TUNER) también
podrá
seleccionarse
presionando
BAND
y
después
uno
de
STATION
PRESET.
Se
seleccionará la última emisora de la banda
previamente seleccionada.
Para escuchar con auriculares
Enchufe unos auriculares con clavija estándar de
6,3 mm de diámetro en la toma PHONES.
Utilización de la bandeja de control
Además de los botones y controles de la unidad
principal y del controlador remoto, existe un panel
de control replegable en el amplificador.
Para desplegar la etapa de control
Presione OPEN/CLOSE para desplegarla bandeja.
La bandeja también se abrirá cuando presione DSP.
Sin embargo, si no realiza ninguna operación
durante unos 8 segundos, la bandeja se replegará
automáticamente.
Para replegar la bandeja de control
Vuelva a presionar OPEN/CLOSE para replegar
la bandeja, o presione ésta ligeramente hacia
adentro. La bandeja se replegará dentro del
amplificador.
Guía de iluminación O
Cuando presione uno de los botones FUNCTION,
se encenderán o parpadearán otros botones para
facilitar el seguir la secuencia de pasos.
Ejemplo: Escucha del sintonizador
Cuando presione TUNER, se encenderán los
botones STATION PRESET.
Avant d’utiliser la chaîne, l’installer comme illustré
pages 64 à 69.
Pour allumer la chaîne
Branchez le cordon secteur et appuyez sur
POWER.
Pour sélectionner une source
Après avoir allumé la chaîne, appuyez sur une
des touches de sélection de FUNCTION.
La fonction CD ou TAPE est sélectionnée et la
lecture commence si vous appuyez sur la touche
de lecture correspondante. La lecture ne peut
cependant pas commencer si aucun CD ou
cassette n’est en place.
Vous pouvez également sélectionner la fonction
TUNER en appuyant sur BAND puis sur une
touche STATION PRESET. La dernière station
de la dernière gamme d’ondes est sélectionnée.
Pour écouter au casque
Branchez un casque avec une fiche standard
6,3 mm sur la prise PHONES.
Utilisation du pupitre de commande
En plus des touches et des commandes de
l’appareil principal et de la télécommande, vous
avez
également
accès
à
un
panneau
de
commande rétractable sur l’amplificateur.
Pour ouvrir le pupitre de commande
Appuyez sur OPEN/CLOSE pour sortir le pupitre
de commande. Il s’ouvre également lorsque vous
appuyez sur la touche DSP. Cependant, si vous
n’actionnez aucune commande pendant environ
8
secondes,
le
pupitre
se
referme
automatiquement.
Pour fermer le pupitre de commande
Appuyez de nouveau sur OPEN/CLOSE pour
fermer le pupitre, ou poussez-le légèrement. Le
pupitre rentre dans l’amplificateur.
Assistance lumineuse O
Lorsque vous appuyez sur une des touches de
FUNCTION,
d’autres
touches
s'allument
ou
clignotent pour vous guider dans les différentes
manipulations à effectuer.
Exemple: Pour écouter le tuner
Lorsque vous appuyez sur TUNER, les touches
STATION PRESET s’allument.
10