Programming channels into the tv’s channel memory, Programming channels automatically – Toshiba 32HLX95 User Manual
Page 40
Attention! The text in this document has been recognized automatically. To view the original document, you can use the "Original mode".
![background image](/manuals/671375/40/background.png)
Chapter 6: Setting up your TV
Programming channels into the TV’s channel memory
When you press CHANNEL ÂW on the remote control or TV
top panel, your TV will stop only on the channels stored in the
TVs channel memory.
Follow the steps below to program channels into the TVs
channel memory.
Programming channels automatically
Your TV can automatically detect all active channels in your area
and store them in its memory. After the channels are
programmed automatically, you can manually add or erase
individual channels.
Note:
• You must configure the antenna input sources before
programming channels [see page 39].
• If the input signal type is set to Cable for an antenna input, the
automatic channel programming process erases channels that
were previously programmed into the TV’s memory.
• If the input signal type Is set to Antenna, the automatic channel
programming process does NOT erase channels that were
previously programmed into the TV's memory, but adds newiy
found channeis to the existing set of programmed channels. To
remove a channel from the memory, you must manually delete it
[see next page].
• To tune the TV to a channel not programmed in the channel
memory, you must use the Channel Number buttons on the
remote control.
• Programming channels for an antenna input configured for
Cabie win take substantially longer than for an antenna input
configured for Antenna. This is normai; however, once channei
programming is completed, you should not have to repeat the
programming process again unless your Cable TV service lineup
changes significantly.
• If you have a CableCARD'^ inserted [page 15], channel
programming for ANT 1 is disabled because the CableCARD^^
automatically loads the Cable channel list into the TV’s channel
memory.
To program channels automatically:
1. Make sure you have configured the antenna input sources.
See page 39 for details.
2. Press MENU and open the Setup menu.
3. Highlight Installation and press ENTER. (A new set of
Installation menu icons will appear on-screen.)
áíM
m
Sleep Timer
On Off lirner
PC Settings
HDMI Audio
Auto
is Gray Level
2
(^{Navigate Select fiiilAijlBack
Exit
4. Open the Terrestrial menu, highlight Channel Program,
and press ENTER.
5. Highlight ANT 1 or
ANT 2, depending on
which antenna input
you want to program
channels for, and then
press ENTER to start
automatic channel
programming.
0
Navigate
'"4;
Select QO Back
0
QÜ Exit
s; Input Configuration
Channei Program
ii Channel Add/Delete
ss Signal Meter
3 ANT2
A ANT 1 Antenna
Scanning channels, please wait
The TV will automatically cycle through all the channels
for the antenna input you selected, and store all active
channels in the channel memory. While the TV is cycling
through the channels, the message “Scanning channels,
please wait” appears (as shown above).
6. To cancel channel programming, either press EXIT or
highlight Abort in the on-screen display and press ENTER.
When channel programming is done, press CHANNEL
AT
to view the programmed channels.
© 0 ©
© 0 ® ,
© ® ®
®
( o ) @
o ®
■ Channel
Numbers
■MENU
PBC _________
(CHRTNl {n//VCRl (
recall
^ fErTl
SLOWOT
SMP
(■(^O'CED c^ic^)
REW PAÜSEÆTEP PUY FP
TV top panel
ENTER
CHANNEL^
c.....::i ..... 1 u-l------- 1----1 1, 1 1
EXIT--------
t * '
1 1
CHANNELT / ▲
MENU
[ENTER]
40
Copyright © 2005 TOSHIBA CORPORATION. All rights reserved.