Flintec FT-15D - Manual (Page 47)

FT-15(D) Technical Manual, Rev. 1.02 August 2010 Page 47 of 52
A PPENDIX 3: E RROR T ABLE
The FT-1x weight indicators have been designed as very reliable and virtually error free instruments. However if
an error occurs do not attempt to repair the equipment before you understand what caused the error. Note the
problems you have with your instrument and the error messages shown on the display. Then try to solve the
problem according to the error table given below.
Error
Code
Description Actions to take / Possible cause FT-15 FT-15D
Under Weight is too low X X
Over Over Load
Check the load;
Load cell or instrument could be defective
X X
Adc Out Input signal outside the input range
Check the load; Check the calibration;
Load cell or instrument could be defective
X
no Prn
There is no serial interface configured
for printing reports or tickets
Configure the printer interface X X
no rCr No alibi record Check the numerical entry X X
rCr Er Alibi record data error Change alibi memory board if this error appears for all CN X X
Empty No data X X
ChAnGE Same code already exists in memory Change vehicle ID code X X
Cod FL Temporary memory is full Wait for the any 2 nd weighing cycle or check the memory X X
E E E Load not within zero range See parameter [202] in chapter 9.4 X X
Err 1
ADC error respective Re-energize indicator.If seen again contact FLINTEC. X
Err 2
Calibration error Adjust DLC eccentricity; Parameter [320] X X
Err 3 Indicator cannot get calibrated Check load cell and load; Repeat the calibration X X
Err 10 EEPROM error Configure the instrument; EEPROM defective X X
Err 20 Calibration error Calibrate the indicator X X
Err 21 Configuration error Configure the indicator X X
Err 22
Tare, CN, Total weight + the SP, PT +
ID in use error Check SP, PT + ID entries; Check Tare, CN + Total
weight
X X
Err 23 Header Error Reload the header X X
Err 24 Footer Error Reload the footer X X
Err 27 Indicator is not calibrated Calibrate the indicator X X
Err 28 Date & Time error Adjust Date & Time; replace battery X X
Err 29 ID error Reload ID information X X
Err 30 Processor Error Contact FLINTEC X X
Err 34 Indicator cannot get calibrated Load cell signal is negative, very low or too high X X
Err 35 Calibration Error
Calibration test weight is too small;
Check load cell connections
X X
Err 37 Scale unstable
Wait until scale becomes stable;
Check ground connection
X X
Err 40 Alibi memory error Correct parameter [801]; Alibi memory card broken X X
Err 41 New alibi card installed X X
Err 42 Alibi card serial no. is not identical
Appears when new alibi memory card is installed (*)
X X
Err 43
Alibi card serial no. is not identical, no
print operation will be performed
Identify the alibi memory card to the indicator (*) X X
Err 44 Alibi card info error X X
Err 46 Alibi recording capacity error X X
Err 47 Info error from weighing board X X
Err 50 DLC board not detected X
Err 61 U10 (eeprom) is not installed X X
Err 62 U8 (eeprom) is not installed X X
E XXXX Hardware error
Re-energize indicator.
If seen again contact FLINTEC.
X X
Ed1 yy ** Communication time out X
Ed2 yy ** Checksum error
Check DLC (RS-485) hardware; Check DLC cables;
Check DLCs and serial number;
Contact FLINTEC
X
Ed3 yy ** DLC error Check ambient temperature; Replace DLC X
Ed4 yy ** DLC is under X
Ed5 yy ** DLC is over
Check mechanical installation and DLC
X
Ed6 yy ** DLC communication error
Check DLC (RS-485) hardware; Re-energize indicator;
Re-define DLC address
X
Ed7 yy ** DLC address and SN matching error
Check serial number; Re-define DLC address;
Replace DLC
X
Ed0 yy ** DLC status error Replace DLC X
* see chapter 9
** yy = number of DLC