Verilink QUAD DATA (880-503319-001) Product Manual - Manual (Page 20)

Quick Set-Up
2-6 Verilink QUAD DATA User Manual
Adding a Circuit Type “A” to access the Add Circuit Menu. See Figure 2-5 .
Figure 2-5 Add Circuit Menu
1. Use the N command to give the circuit a name. For the first
circuit use “QUADDATA_P1”.
2. Use the M command to set the mode to 64K, this means that
for each DS0 timeslot used, we will use the full 64K of
bandwidth.
NOTE: When mapping a data port to a T1 network port connected to
an AMI T1 facility, use 56K for the mode option.
3. Use the SP command to set the source port to shelf 1, slot 3,
data port 1. When configuring a circuit to a QUAD DATA
module, DS0 timeslots are not specified. The data rate is set
when the network port is configured.
4. Use the DP command to set the destination port to shelf 1, slot
2—the M1-3 multiplexer module. New fields appear on the
menu,
DM DM DM DM for destination port DS0 mapping and DT DT DT DT for
destination port T1 mapping.
5. Use the DM command to select all 24 DS0s and use the DT
command to select T1 number 4 of the 28 available virtual T1
circuits.
6. When the Setup command is used, the SCM will select the
midplane bus for this circuit.
7. Type “S” to setup the circuit. A message should appear
Successful Circuit Build Successful Circuit Build Successful Circuit Build Successful Circuit Build.
This completes the configuration of the first example circuit. For
the next circuit, begin by cloning from the existing circuit.
-- ADD CIRCUIT MENU [1,1] SCM Firmware 1.12 -- -- ADD CIRCUIT MENU [1,1] SCM Firmware 1.12 -- -- ADD CIRCUIT MENU [1,1] SCM Firmware 1.12 -- -- ADD CIRCUIT MENU [1,1] SCM Firmware 1.12 --
N) name: -- M) mode: -- N) name: -- M) mode: -- N) name: -- M) mode: -- N) name: -- M) mode: --
SP) src port: [-,-] undefined DP) dst port: [-,-] undefined SP) src port: [-,-] undefined DP) dst port: [-,-] undefined SP) src port: [-,-] undefined DP) dst port: [-,-] undefined SP) src port: [-,-] undefined DP) dst port: [-,-] undefined
--port rate selection-- --port rate selection--
--port rate selection-- --port rate selection-- --port rate selection-- --port rate selection-- --port rate selection-- --port rate selection--
( undefined port ) ( undefined port )
( undefined port ) ( undefined port ) ( undefined port ) ( undefined port ) ( undefined port ) ( undefined port )
( undefined port ) ( undefined port )
( undefined port ) ( undefined port ) ( undefined port ) ( undefined port ) ( undefined port ) ( undefined port )
( undefined port ) ( undefined port )
( undefined port ) ( undefined port ) ( undefined port ) ( undefined port ) ( undefined port ) ( undefined port )
( undefined port ) ( undefined port )
( undefined port ) ( undefined port ) ( undefined port ) ( undefined port ) ( undefined port ) ( undefined port )
bus: AUT ->-->>->> Circuit Inactive <<-<<--<- bus: AUT ->-->>->> Circuit Inactive <<-<<--<- bus: AUT ->-->>->> Circuit Inactive <<-<<--<- bus: AUT ->-->>->> Circuit Inactive <<-<<--<-
S) setup X) exit S) setup X) exit S) setup X) exit S) setup X) exit
A [0.0.0.2] [1,1] SCM > A [0.0.0.2] [1,1] SCM > A [0.0.0.2] [1,1] SCM > A [0.0.0.2] [1,1] SCM >