Document Outline

• Contents
• 1. Introduction
  • 1.1 Safe Use of This Product
  • 1.2 Radio Wave
  • 1.3 Warranty
  • 1.4 Trademarks
  • 1.5 ATEX Documentation
• 2. Handling Cautions
  • 2.1 Model and Specifications Check
  • 2.2 Unpacking
  • 2.3 Storage
  • 2.4 Selecting the Installation Location
  • 2.5 Pressure Connection
  • 2.6 Restrictions on Use of Radio Transceivers
  • 2.7 Insulation Resistance and Dielectric Strength Test
  • 2.8 Installation of an Explosion-Protected Instrument
    • 2.8.1 FM Approval
    • 2.8.2 CSA Certification
    • 2.8.3 ATEX Certification
    • 2.8.4 IECEx Certification
  • 2.9 EMC Conformity Standards
  • 2.10 Pressure Equipment Directive (PED)
  • 2.11 Low Voltage Directive
  • 2.12 Regulatory Compliance for Radio and Telecommunication
    • 2.12.1 Radio and Telecommunications
    • 2.12.2 FCC compliance
    • 2.12.3 Industry Canada (IC) compliance
• 3. Component Names
• 4. Installation
  • 4.1 Precautions
  • 4.2 Mounting
  • 4.3 Changing the Process Connection
  • 4.4 Swapping the High/Low-pressure Side Connection
    • 4.4.1 Rotating Pressure-detector Section 180°
    • 4.4.2 Using the Configuration Tool
  • 4.5 Rotating Transmitter Section
  • 4.6 Changing the Direction of Integral Indicator
  • 4.7 Changing the direction of the antenna
• 5. Installing Impulse Piping
  • 5.1 Impulse Piping Installation Precautions
    • 5.1.1 Connecting Impulse Piping to a Transmitter
    • 5.1.2 Routing the Impulse Piping
  • 5.2 Impulse Piping Connection Examples
• 6. Wiring
  • 6.1 Mounting Antenna and Wiring
    • 6.1.1 Mounting the antenna
    • 6.1.2 Mounting External Antenna and Wiring Antenna Extension Cable
    • 6.1.2.1 Mounting of External Antenna
    • 6.1.2.2 Wiring of Antenna Extension Cable
    • 6.1.2.3 Mounting of Arrester and Wiring
  • 6.2 Grounding
• 7. Operation
  • 7.1 Preparation for Starting Operation
  • 7.2 Zero Point Adjustment
  • 7.3 Starting Operation
  • 7.4 Connecting to the Field Wireless Network
  • 7.5 Shutting Down the Transmitter
  • 7.6 Venting or Draining Transmitter Pressure-detector Section
    • 7.6.1 Draining Condensate
    • 7.6.2 Venting Gas
• 8. Setting Parameters
  • 8.1 Environment for parameter setting
  • 8.2 Preparing Software
    • 8.2.1 Softwares for the Field Wireless Configuration Tool and the Device Configuration Tool
    • 8.2.2 Software Download
  • 8.3 Setting Parameters
    • 8.3.1 Parameter Usage and Selection
    • 8.3.2 Function Block and Menu Tree
    • 8.3.3 Parameters for Wireless Communication
    • 8.3.4 Tag and Device Information
    • 8.3.5 Unit
    • 8.3.6 Range Change
    • 8.3.7 Output Mode
    • 8.3.8 Output Signal Low Cut Mode Setup
    • 8.3.9 Impulse Line Connection Orientation Setup
    • 8.3.10 Integral Indicator Display Mode
    • 8.3.11 Integral Indicator Scale Setup
    • 8.3.12 Unit for Displayed Temperature
    • 8.3.13 Unit for Displayed Static Pressure
    • 8.3.14 Zero Point Adjustment and Span Adjustment
    • 8.3.15 Software Write Protect
    • 8.3.16 Switching to Deep Sleep Mode
    • 8.3.17 Switching to Silence Mode
  • 8.4 Self-Diagnostics
    • 8.4.1 Identify Problems by Using the Device Configuration Tool
    • 8.4.2 Alert Report
    • 8.4.3 Checking with Integral Indicator
• 9. Maintenance
  • 9.1 Overview
  • 9.2 Calibration Instruments Selection
  • 9.3 Calibration
  • 9.4 Disassembly and Reassembly
    • 9.4.1 Replacing the Integral Indicator
    • 9.4.2 Replacing the RF Assembly
    • 9.4.3 Replacing the CPU Assembly
    • 9.4.4 Cleaning and Replacing the Capsule Assembly
    • 9.4.5 Replacing the Process Connector Gaskets
    • 9.4.6 Replacing the Battery Pack
    • 9.4.7 Replacing the Batteries
    • 9.4.8 Handling Batteries
  • 9.5 Troubleshooting
    • 9.5.1 Basic Troubleshooting
    • 9.5.2 Troubleshooting Flowcharts
    • 9.5.3 Errors and Countermeasures
• 10. Parameter Summary
• 11. General Specifications
  • 11.1 Standard Specifications
  • 11.2 Model and Suffix Codes
  • 11.3 Optional Specifications
  • 11.4 Dimensions
• Revision Information