KORG MICROX X50 - Manual (Page 127)

120
a: Ctrl, e: V1 Reso, h: V2 Reso
This parameter determines the resonance intensity.
When “Ctrl” = Manual, the “Reso” parameter sets the intensity of
resonance. If the “Reso” parameter has a negative value, harmon-
ics will be changed, and resonance will occur at a pitch one octave
lower.
When “Ctrl” = LFO, the intensity of resonance varies according to
the LFO. The LFO sways between positive and negative values,
causing resonance to occur between specified pitches an octave
apart in turn.
When “Ctrl” = Dmod, the resonance is controlled by the dynamic
modulation source. If JS X or Rbn#16 is assigned as the modula-
tion source, the pitch an octave higher and lower can be con-
trolled, similar to when LFO is selected for Control Mode.
a: Invert
When “Ctrl” = LFO or Dmod, the controlled phase of either Voice
1 or 2 will be reversed. When the resonance pitch is set for Voice 1
(Resonance has a positive value), Voice 2 will resonate at a pitch
an octave below (Resonance has a negative value).
d: V1 Pitch, d: Fine, g: V2 Pitch, g: Fine
The Pitch parameter specifies the pitch of resonance by note
name. The “Fine” parameter allows for fine adjustment in steps of
cents.
e: HiDamp, h: HiDamp
This parameter sets the damping amount of resonant sound in the
high range. Lower values will make a metallic sound with a
higher range of harmonics.
30: Doppler
This effect simulates the “Doppler effect” of a moving sound
with a changing pitch, similar to the siren of an passing
ambulance. Mixing the effect sound with the dry sound will
create a unique chorus effect.
a: Mode, a: Src, b: LFO Sync
The “Mode” parameter switches LFO operation mode. When
Loop
is selected, the Doppler effect will be created repeatedly. If
“LFO Sync” is set to On, the LFO will be reset when the modula-
tion source specified with the “Src” parameter is turned on.
When “Mode” is set to 1-Shot, the Doppler effect is created only
once when the modulation source specified in the “Src” field is
turned on. At this time if you do not set the “Src” parameter, the
Doppler effect will not be created, and no effect sound will be out-
put.
The effect is off when a value for the modulation source
specified for the “Src” parameter is smaller than 64, and the
effect is on when the value is 64 or higher. The Doppler
effect is triggered when the value changes from 63 or
smaller to 64 or higher.
e: Pitch Dep
With the Doppler effect, the pitch is raised when the sound
approaches, and the pitch is lowered when the sound goes away.
This parameter sets this pitch variation.
f: Pan Dep
This parameter sets the width of the stereo image of the effect
sound. With larger values, the sound seems to come and go from
much further away. With positive values, the sound moves from
left to right; with negative values, the sound moves from right to
left.
a
Mode (LFO Mode)
Switches LFO operation mode Loop, 1-Shot
☞ ,
Src (Source) Off...Tempo
When LFO Mode is set to 1-Shot, this modulation source triggers the
LFO
☞
b
LFO Sync Off, On
Switches between LFO reset on and off when LFO Mode is set to
Loop
☞
c
Freq (LFO Frequency) 0.02...20.00Hz
Sets the LFO speed ☞ Fx:09,
(Source)
Selects the modulation source of LFO speed Off...Tempo
(Amount) –20.00...+20.00Hz
Sets the modulation amount of LFO speed
d
BPM/MIDI Sync Off, On
Switches between using the frequency of the LFO speed and using
the tempo and notes
☞ Fx:09,
BPM
Selects MIDI Clock and assigns tempo MIDI, 40...240
☞ Fx:09
Base (Base Note)
Selects the type of notes that specify the LFO speed ☞ Fx:09
Times 1...16
Sets the number of notes that specify the LFO speed ☞ Fx:09
Left
Right
Wet / Dry
Wet / Dry
Wet: Mono In - Stereo Out / Dry: Stereo In - Stereo Out
Pan Depth
D -mod
+
Trigger LFO Mode = 1-Shot
Doppler
LFO
e
Pitch Dep (Pitch Depth)
Sets the pitch variation of the moving sound 0...100
☞ ,
(Source)
Selects the modulation source of pitch variation Off...Tempo
(Amount)
Sets the modulation amount of pitch variation –100...+100
f
Pan Dep (Pan Depth)
Sets the panning of the moving sound –100...+100
☞ ,
(Source)
Selects the modulation source of panning Off...Tempo
(Amount)
Sets the modulation amount of panning –100...+100
g
W/D (Wet/Dly) Dry, 1:99...99:1, Wet
Sets the balance between the effect and dry sounds
(Source) Off...Tempo
Selects the modulation source of the effect balance
(Amount)
Sets the modulation amount of the effect balance –100...+100
Pitch
Higher
Doppler - Pitch / Pan Depth
Lower
Original Pitch
Left Center Right
Pitch Depth
Pan Depth
< < < < < <<<<<< >>>>>> > > > > >
Volume Louder Louder
Pan Depth
= (–) value Pan Depth
= (+) value