Combi 4: ed-midi filter2, 1: midi 2-1 (midi filter 2-1), 2: midi 2-2 (midi filter 2-2) – KORG MICROX X50 User Manual
Page 51: X50: 4-3: midi 2-3 (midi filter2-3), X50: 4-4: midi 2-4 (midi filter 2-4), Microx: 4-3: midi 2-3 (midi filter2-3), Combi 4: ed–midi filter2, 4–1: midi 2–1 (midi filter 2–1), 4–2: midi 2–2 (midi filter 2–2), 4–3: midi 2–3 (midi filter2–3)
44
COMBI 4: Ed–MIDI Filter2
Specifies whether the A- and B-mode effects of REALTIME
CONTROLS knobs [1], [2], [3], and [4] will be transmitted
and received. The A-mode of each knob is fixed as a MIDI
control change message. For B-mode, you can assign a MIDI
control change message in 7: Ed–Arp/Ctrls.
X50:
Specifies whether the effects of [SW1] and [SW2] will
be received. The assignable switches [SW1] and [SW2] corre-
spond to the messages that are assigned to the 7: Arp/Ctrls,
Controls page.
4–1: MIDI 2–1
(MIDI Filter 2–1)
4–1a: Real-time Control Knob 1, 2
Knob1
[Off, On]
Specifies whether MIDI control change message #74 (inter-
nal low pass filter cutoff frequency) for the A-mode of knob
[1] and the MIDI control change message assigned to the B-
mode of knob [1] will be transmitted and received.
Knob2
[Off, On]
Specifies whether MIDI control change message #71 (inter-
nal low pass filter resonance or high pass filter cutoff fre-
quency) for the A-mode of knob [2] and the MIDI control
change message assigned to the B-mode of knob [2] will be
transmitted and received.
■ 4–1: UTILITY
☞“Write Combination,” “Solo Selected Timbre” (0–1)
4–2: MIDI 2–2
(MIDI Filter 2–2)
4–2a: Real-time Control Knob 3, 4
Knob3
[Off, On]
Specifies whether MIDI control change message #79 (inter-
nal filter EG intensity) for the A-mode of knob [3] and the
MIDI control change message assigned to the B-mode of
knob [3] will be transmitted and received.
Knob4
[Off, On]
Specifies whether MIDI control change message #72 (inter-
nal filter and amp EG release time) for the A-mode of knob
[4] and the MIDI control change message assigned to the B-
mode of knob [4] will be transmitted and received.
■ 4–2: UTILITY
☞“Write Combination,” “Solo Selected Timbre” (0–1)
X50:
4–3: MIDI 2–3
(MIDI Filter2–3)
4–3a: SW1, SW2
SW1, SW2
[Off, On]
Specifies whether the operations of [SW1] and [SW2] will be
transmitted and received.
These correspond to the control change messages assigned
in 7: Ed–Arp/Ctrls.
This filter setting is valid for settings of SW1 Mod.(CC#80),
SW2 Mod.(CC#81), or Porta.SW(CC#65).
■ 4–3: UTILITY
☞“Write Combination,” “Solo Selected Timbre” (0–1)
X50:
4–4: MIDI 2–4
(MIDI Filter 2–4)
microX:
4–3: MIDI 2–3
(MIDI Filter2–3)
X50
microX
4–1a
4–2a
4–3a
4–4a
4–3a