X50: sw1/2 assign, Sw1, sw2 assign list, Sw1/2 assign – KORG MICROX X50 User Manual
Page 168: P.161 “sw1, sw2, These settings assign functions to [sw1] and [sw2, P.161, Sw1, sw2 assign list”), P.161 “sw1, sw2 assign list”), Assign list”), P.161 “x50: sw1/2
161
Ap
pendic
es
X50:
SW1/2 Assign
The following functions can be assigned to the assignable
switches [SW1] and [SW2].
• For a program, combination, or multi set make the
settings in 7: Ed–Arp/Ctrls page “SW1/2 Assign”
(PROG 7–3a, COMBI 7–5b, MULTI 7–5b).
This can be set for each program in Program mode,
each combination in Combination mode, and each
multi set in Multi mode.
SW1, SW2 Assign List
SW1 Mod.(CC#80) (SW1 Modulation:CC#80)
SW2 Mod.(CC#81) (SW2 Modulation:CC#81)
This effect differs between SW1 and SW2. SW1 is handled as
CC#80, and SW2 is handled as CC#81.
Porta.SW(CC#65) (Portamento Switch:CC#65)
When “Mode (Oscillator Mode)” (PROG 1–1a) is Single,
turning the switch on (LED lit) will apply portamento
regardless of the “Enable (Porta. Enable)” (PROG 2–1c) set-
ting, and turning the switch off (LED off) will not apply por-
tamento.
If “Mode (Oscillator Mode)” is Double, and if the “Enable
(Porta. Enable)” setting is the same for OSC1 and 2 (i.e.,
Enable
or Disable for both OSC1 and 2), then portamento
will be applied to OSC1 and 2 when the switch is turned on
(LED lit), and portamento will not be applied to OSC1 and 2
when the switch is turned off (LED off).
If the “Enable (Porta. Enable)” setting is different for OSC1
and 2 (i.e., OSC1 is Enable and OSC2 is Disable, or OSC1 is
Disable
and OSC2 is Enable), then portamento will be
applied to the OSC whose setting is Enable when the switch
is turned on (LED lit), and portamento will be applied to
neither OSC when the switch is turned off (LED off).
Pitch Bend Lock
The state of the [PITCH] wheel will alternate between Lock
and Unlock (Lock when the LED is lit).
While the [PITCH] wheel is being operated, turning Lock on
will lock (fix) the effect at the current position of that con-
troller.
For example if you move the [PITCH] wheel in the up direc-
tion and turn Lock on, the [PITCH] wheel movement will be
locked (held) at that position, so that modulation will con-
tinue to be applied even if you return the [PITCH] wheel to
its original position. By continuing to operate the [PITCH]
wheel, you can apply both types of modulation simulta-
neously.
When you Lock the [PITCH] wheel will be halted, but
reception will still occur.
Off
no function
SW1 Mod.(CC#80) (SW1 Modulation:CC#80)
SW2 Mod.(CC#81) (SW2 Modulation:CC#81)
Select this when using the switch as an Alternate Modulation or Effect Dynamic Modulation source.
In this case, you must first specify the control destination. Each time the switch is turned On/Off, a
CC#80 (or CC#81) message will be transmitted (Off: 0, On: 127).
Porta.SW(CC#65) (Portamento Switch:CC#65)
When you press SW1 (or SW2) to turn it on (LED lit), portamento will be applied. Each time this is
turned On/Off, CC#65 will be transmitted (Off: 0, On: 127).
Octave Down
Each time you press SW1 (or SW2), the pitch will alternate between 1 octave lower and the original
octave setting (1 octave down when the LED is lit).
Octave Up
Each time you press SW1 (or SW2), the pitch will alternate between 1 octave higher and the origi-
nal octave setting (1 octave up when the LED is lit).
Pitch Bend
Lock the effect of [PITCH] wheel