KORG MICROX X50 - Manual (Page 131)

124
a: Type, b: LFO Phase
Select the type of phaser LFO and tremolo LFO for the “Type”
parameter. How the effect sound moves or rotates depends on the
type of LFO. Selecting “LFO Phase” enables you to offset the tim-
ing of the phaser peak and control a subtle movement and rota-
tion of the sound.
f: P W/D, i: W/D
The “P W/D” parameter sets the balance between the phaser out-
put and the dry sound. The “W/D” parameter sets the balance
between the final phaser and tremolo output level and the dry
sound.
36: St.Ring Mod
(Stereo Ring Modulator)
This effect creates a metallic sound by applying the oscillators
to the input signal. Use the LFO or Dynamic Modulation to
modulate the oscillator to create a radical modulation. Match-
ing the oscillator frequency with a note number will produce
a ring modulation effect in specific key ranges.
a: Pre LPF
This parameter enables you to set the damping amount of the
high range sound input to the ring modulator. If the input sound
contains lots of harmonics, the effect may sound dirty. In this case,
cut a certain amount of high range.
b: OSC Mode
This parameter determines whether or not the oscillator fre-
quency follows the note number.
c: F
This parameter sets the oscillator frequency when “OSC Mode” is
set to Fixed.
d: Note Offset, d: Fine
These parameters for the oscillator are used when “OSC Mode” is
set to Note (Key Follow). The “Note Offset” sets the pitch differ-
ence from the original note in semitone steps. The “Fine” parame-
ter fine-adjusts the pitch in cent steps. Matching the oscillator
frequency with the note number produces a ring modulation
effect in the correct key.
h
T Dep (Tremolo Depth)
Sets the tremolo modulation depth 0...100
(Source) Off...Tempo
Selects the modulation source for the tremolo modulation depth
(Amount) –100...+100
Sets the modulation amount of the tremolo modulation depth
i
W/D (Wet/Dly) Dry, 1:99...99:1, Wet
Sets the balance between the effect and dry sounds ☞ ,
(Source) Off...Tempo
Selects the modulation source of the effect balance
(Amount)
Sets the modulation amount of the effect balance –100...+100
a
Pre LPF 0...100
Sets the damping amount of the high range input to the ring modula-
tor
☞
b
OSC Mode Fixed, Note (Key Follow)
Switching between specifying the oscillator frequency and using a
note number
☞
c
F (Fixed Frequency) 0...12.00kHz
Sets the oscillator frequency when OSC Mode is set to Fixed
☞ ,
(Source) Off...Tempo
Selects the modulation source for the oscillator frequency when OSC
Mode is set to Fixed
(Amount) –12.00...+12.00kHz
Sets the modulation amount of the oscillator frequency when OSC
Mode is set to Fixed
d
Note Offset –48...+48
Sets the pitch difference from the original note when OSC Mode is
set to Note (Key Follow)
☞
Fine (Note Fine)
Fine-adjusts the oscillator frequency –100...+100
☞
Left
Right
Wet / Dry
Wet / Dry
Stereo In - Stereo Out
Pre LPF
Ring Modulator
Pre LPF
Ring Modulator
Note No.
OSC Mode
Fixed
Note (Key Follow)
Fixed Frequency
Pitch
Note Offset, Fine
Sine Oscillator
LFO
e
lfoF (LFO Frequency) 0.02...20.00Hz
Sets the LFO speed of the oscillator frequency modulation
☞ Fx:09,
(Source)
Selects the modulation source of LFO speed Off...Tempo
(Amount) –20.00...+20.00Hz
Sets the modulation amount of LFO speed
f
BPM/MIDI Sync Off, On
Switches between using the frequency of the LFO speed and using
the tempo and notes
☞ Fx:09,
BPM
Selects MIDI Clock and assigns tempo MIDI, 40...240
☞ Fx:09
Base (Base Note)
Selects the type of notes that specify the LFO speed ☞ Fx:09
Times 1...16
Sets the number of notes that specify the LFO speed ☞ Fx:09
g
Depth (LFO Depth) 0...100
Sets the depth of LFO modulation for the oscillator frequency
(Source) Off...Tempo
Selects the modulation source of the depth of modulation
(Amount) –100...+100
Sets the modulation amount of the depth of modulation
h
W/D (Wet/Dly) Dry, 1:99...99:1, Wet
Sets the balance between the effect and dry sounds
(Source) Off...Tempo
Selects the modulation source of the effect balance
(Amount)
Sets the modulation amount of the effect balance –100...+100