Ricoh BIZWORKS 106 User Manual
Page 212
© Copyright 1999, RICOH CO., LTD.
Introduction
This manual contains detailed instructions on the operation and maintenance of this machine. To get
maximum versatility from this machine, all operators should carefully read and follow the instructions in
this manual. Please keep this manual in a handy place near the machine.
Please read the safety information on pages i - iii of this manual. It contains Important Information related
to user safety and preventing equipment problems.
Laser Safety:
The optical housing unit can only be repaired in a factory or at a location with the requisite equipment. The
laser subsystem is replaceable in the field by a qualified Customer Engineer. The laser chassis is not
repairable in the field. Customer engineers are therefore directed to return all chassis and laser sub-
systems to the factory or service depot when replacement of the optical subsystem is required.
Notes:
•
Model names for the machines do not appear in the following pages. Check the type of your ma-
chine before reading this manual.
Type 1
Bizworks 406e
Type 2
Bizworks 406eDF
•
Some illustrations may be slightly different from your machine.
•
Certain types may not be available in some countries. For details, contact your local dealer.
Two kinds of size notation are employed in this manual. With this machine refer to the metric version.
For good print quality, Ricoh recommends that you use genuine Ricoh toner.
Ricoh shall not be responsible for any damage or expense that may result from the use of parts other than
genuine Ricoh parts in your Ricoh office product.
Power Source:
120 V, 60 Hz, 4.2 A
Please make sure to connect the power cord to a power source as above. For details about power con-
nection, refer to page 8.
Trademarks
Microsoft
„
, Windows
„
, and MS-DOS
„
are registered trademarks of Microsoft Corporation in the United
States and/or other countries.
Other product names used herein are for identification purposes only and might be trademarks of their
respective companies. We disclaim any and all rights in those marks.
In accordance with ISO Standard 7001, this machine uses the following symbols for the main switch:
a
means POWER ON.
b
means POWER OFF.
INFORMATION TO THE USER
USA FCC Part 15 Class B
NOTE
This equipment has been tested and found to comply with the limits for a Crass B digital device, pursuant
to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may cause harmful interference
to radio communications.
However, there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be deter-
mined by turning the equipment off and on, the user is encouraged to try to correct the interference by one
more of the following measures:
-
Reorient or relocate the receiving antenna.
-
Increase the separation between the equipment and receiver.
-
Connect the equipment into an outlet on a circuit different from that to which the receiver is con-
nected.
-
Consult the dealer or an experienced radio/TV technician for help.
Properly shielded and grounded cables and connectors must be used for connections to host computer in
order to meet FCC emission limits.
WARNING
Changes or modifications not expressly approved by the party responsible for compliance could void the
user’s authority to operate the equipment.
COMPLIANCE INFORMATION STATEMENT
Declaration of Conformity
RICOH Bizworks
406/406DF
RICOH CORPORATION
5 Dedrick Place West Caldwell, New Jersey 07006
973-882-2000
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
CANADA Class B
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.