TOA Electronics D-901 - Manual (Page 65)

65
12.5. Contact Input/Output Settings (Available only when D-981, D-983, or D-984VC is used)
Many different functions assigned to the input and output contacts of the D-981 or D-983 Remote Control
Module, or the D-984VC VCA Control Module can be remotely controlled by connected external equipment.
Use the Setting knob to select the functions to be assigned.
Notes
• To make subsequent settings valid when the power is ON after the initial Contact input/output settings, save
the configuration (p. 60). Settings are saved as system data, and setting status is maintained even if the
preset memory is recalled.
• Configuration can also be saved by pressing the Setting knob at this screen.
12.5.1. Function assignment to the input contact
Each of the following functions can be assigned to input contacts (1 – 8 when the D-981 or D-984VC is used,
and 1 – 24 when the D-983 is used).
Preset memory recall, Input and output channel volume adjustment,
Channel ON/OFF setting, and Line (stereo) input selection
Preset memory
recall
Channel ON/OFF
(Contact)
Line (stereo) input
selection
Channel ON/OFF
(Pulse)
Volume UP
Volume DOWN
Preset number
Input contact
number selection
Channel number
Channel number
Channel number
Slot number/line (stereo)
input number
Channel number
[ U T Y ] R M I N
1 : N O N E
[ U T Y ] R M I N
2 : N O N E
[ U T Y ] R M I N
8 : N O N E
[ U T Y ] R M I N
1 : N O N E
[ U T Y ] R M I N
1 P R E S E T 1
[ U T Y ] R M I N
1 V O L U P I N 1
[ U T Y ] R M I N
1 C H M A K E I N 1
[ U T Y ] R M I N
1 C H P L S I N 1
[ U T Y ] R M I N
1 L i n e S e l S 2 – 1
[ U T Y ] R M I N
1 : L i n e S e l S 2 – 1
[ U T Y ] R M I N
1 : C H P L S I N 1
[ U T Y ] R M I N
1 : C H M A K E I N 1
[ U T Y ] R M I N
1 V O L D OW N I N 1
[ U T Y ] R M I N
1 : V O L D OW N I N 1
[ U T Y ] R M I N
1 : V O L U P I N 1
[ U T Y ] R M I N
1 : P R E S E T 1
Setting items are the same as above.
Setting items are the same as above.
NOM attenuation settings (previous page)
Output contact number selection (p. 67)
PARAMETER
PUSH-ENTER
CHANGE
PARAMETER
PUSH-ENTER
CHANGE
PARAMETER
PUSH-ENTER
CHANGE
PARAMETER
PUSH-ENTER
CHANGE
PARAMETER
PUSH-ENTER
CHANGE
PARAMETER
PUSH-ENTER
CHANGE
PARAMETER
PUSH-ENTER
CHANGE
PARAMETER
PUSH-ENTER
CHANGE
PARAMETER
PUSH-ENTER
CHANGE
PARAMETER
PUSH-ENTER
CHANGE
PARAMETER
PUSH-ENTER
CHANGE
PARAMETER
PUSH-ENTER
CHANGE
PARAMETER
PUSH-ENTER
CHANGE
[Screen display operations]
No function is assigned.
Select the preset memory number.
Select the channel number.
Select the channel number.
Channels are enabled when the
contact closes, and disabled when
the contact opens.
Enables and disables channels
each time a pulse signal is
received.
Select the slot number and Line
(stereo) input number for the D-
936R or the D-937SP (only when
the D-936R or the D-937SP is
used).
(Example. S2-1: First line (stereo)
input for the stereo module
inserted into Slot 2)