Yamaha Professional Audio Workstation AW4416 - Manual (Page 467)

Appendix
— Reference Guide Appendix–
51
3. MIDI message formats
3.1 CHANNEL MESSAGE
command rx/tx function
-----+----------------------------+-------+-------------------------------
8n NOTE OFF
rx Control internal effects
9n NOTE ON rx Control internal effects
Bn CONTROL CHANGE Only echoed
Cn PROGRAM CHANGE rx/tx Select scene memories
(using the Program
Change Table)
3.2 SYSTEM COMMON MESSAGE
command rx/tx function
-----+----------------------------+-------+-------------------------------
F1 MIDI TIME CODE
rx/tx MTC transmission (when
MTC master), MTC
reception (when MTC
slave)
F2 SONG POSITION
POINTER tx SPP transmission (when
using MIDI Clock)
3.3 SYSTEM REAL TIME MESSAGE
command rx/tx function
-----+----------------------------+-------+-------------------------------
F8 TIMING CLOCK
tx MIDI Clock reception
(when using MIDI Clock)
FA START tx Start command transmis-
sion (when using MIDI
Clock)
FB CONTINUE tx Continue command
transmission (when
using MIDI Clock)
FC STOP tx Stop command transmis-
sion (when using MIDI
Clock)
FE ACTIVE SENSING rx MIDI cable connection
checking
FF RESET rx Clear running status
3.4 SYSTEM EXCLUSIVE MESSAGE
3.4.1 Real Time System Exclusive
3.4.1.1 MMC
command rx/tx function
-----+----------------------------+-------+-------------------------------
01 STOP
rx/tx Transport Stop
02 PLAY rx Transport Play
03 DEFERRED PLAY rx/tx Transport Play
04 FAST FOWARD rx/tx Transport Fast-forward
05 REWIND rx/tx Transport Rewind
06 RECORD STROBE rx Transport Record/Punch-
in
07 RECORD EXIT rx Transport Punch-out
0F RESET rx/tx MMC Reset
40 WRITE rx Write Information Field
44 LOCATE rx/tx Transport Locate
4. MIDI format details
4.1 NOTE OFF (8n)
< Reception >
Received if [Rx CH] matches.
Used to control effects. See below for details.
STATUS 1000nnnn 8n Note Off Message
DATA 0nnnnnnn nn Note No.
0vvvvvvv vv Velocity (ignored)
4.2 NOTE ON (9n)
< Reception >
Received if [Rx CH] matches.
Used to control effects. See below for details.
If velocity is 0x00, same as note-off.
STATUS 1001nnnn 9n Note On Message
DATA 0nnnnnnn nn Note No.
0vvvvvvv vv Velocity (1-127:On,
0:off)
* Notes used to control effects.
1: Dynamic Flange / Dynamic Phase / Dynamic Filter
If the SOURCE parameter is set to MIDI, velocity will con-
trol the width of frequency modulation for both note-on and
note-off.
4.3 CONTROL CHANGE (Bn)
< Reception >
Echoed if [Control Change ECHO] is on.
< Transmission >
If [Control Change ECHO] is on, this is merged with the
AW4416’s own output while taking advantage of running
status.
4.4 PROGRAM CHANGE (Cn)
< Reception >
Received if [Program Change RX] is on and [Rx CH]
matches. However if [OMNI] is on, this is received regard-
less of the channel.
This is echoed if [Program Change ECHO] is on.
A scene memory will be recalled according to the [Program
change table].
< Transmission >
If [Program Change TX] is on, a recall operation will cause a
program change to be transmitted on the [Tx CH] according
to the settings of the [Program change table].
If more than one program number is assigned to the mem-
ory number that was recalled, the lowest-numbered pro-
gram will be transmitted.
If [Program Change ECHO] is on, program changes will be
echoed.
(If a memory number is recalled for which there is no setting
in the [MIDI Program Change Assign Table], no program
change will be transmitted.)
STATUS 1100nnnn Cn Program Change
DATA 0nnnnnnn nn Program No. (0-127)
4.5 MIDI TIME CODE QUARTER FRAME (F1)
< Transmission >
When MTC transmission is selected and the recorder is in
PLAY or REC status, Quarter Frame messages will be trans-
mitted according to the time code operation of the recorder.
< Reception >
These messages are received if the AW4416 is operating as
a MTC slave. Quarter Frame messages received in realtime
are assembled internally to create time code values that
control the recorder.