Watlow Series 146 Retrofit - Manual (Page 111)

Series 146
Series 146
Line
Voltage Input Temp Range
Control
Mode Action Output Set Point Mounting Retrofit control
See Notes
Below
146E-3T1D-3100 24 VAC T t/c -200 to 350°C High Limit Auto Reset 10A Relay Integral DIN Rail LV G6NW -200 0350 A 3, 6, 8
146E-3T1D-3200 24 VAC T t/c -328 to 662°F High Limit Auto Reset 10A Relay Remote DIN Rail LV G5MW -328 0662 A 2, 3, 6, 8
146E-3T1D-3200 24 VAC T t/c -200 to 350°C High Limit Auto Reset 10A Relay Remote DIN Rail LV G5NW -200 0350 A 2, 3, 6, 8
146E-3T1D-4100 24 VAC T t/c -328 to 662°F Low Limit Auto Reset 10A Relay Integral DIN Rail LV G6MZ -328 0662 A 3, 6, 8
146E-3T1D-4100 24 VAC T t/c -200 to 350°C Low Limit Auto Reset 10A Relay Integral DIN Rail LV G6NZ -200 0350 A 3, 6, 8
146E-3T1D-4200 24 VAC T t/c -328 to 662°F Low Limit Auto Reset 10A Relay Remote DIN Rail LV G5MZ -328 0662 A 2, 3, 6, 8
146E-3T1D-4200 24 VAC T t/c -200 to 350°C Low Limit Auto Reset 10A Relay Remote DIN Rail LV G5NZ -200 0350 A 2, 3, 6, 8
146E-3T1F-1100 24 VAC T t/c -328 to 662°F High Limit Manual Reset 10A Relay Integral DIN Rail LV G6MU -328 0662 A 3, 6
146E-3T1F-1200 24 VAC T t/c -328 to 662°F High Limit Manual Reset 10A Relay Remote DIN Rail LV G5MU -328 0662 A 2, 3, 6
146E-3T1F-2100 24 VAC T t/c -328 to 662°F Low Limit Manual Reset 10A Relay Integral DIN Rail LV G6MY -328 0662 A 3, 6
146E-3T1F-2200 24 VAC T t/c -328 to 662°F Low Limit Manual Reset 10A Relay Remote DIN Rail LV G5MY -328 0662 A 2, 3, 6
146E-3T1F-3100 24 VAC T t/c -328 to 662°F High Limit Auto Reset 10A Relay Integral DIN Rail LV G6MW -328 0662 A 3, 6
146E-3T1F-3200 24 VAC T t/c -328 to 662°F High Limit Auto Reset 10A Relay Remote DIN Rail LV G5MW -328 0662 A 2, 3, 6
146E-3T1F-4100 24 VAC T t/c -328 to 662°F Low Limit Auto Reset 10A Relay Integral DIN Rail LV G6MZ -328 0662 A 3, 6
146E-3T1F-4200 24 VAC T t/c -328 to 662°F Low Limit Auto Reset 10A Relay Remote DIN Rail LV G5MZ -328 0662 A 2, 3, 6
Note 1: Retrofit controller requires a substitution of a 100 Ohm DIN RTD sensor.
Note 2: Mounting and dimensions of retrofit controller are different. Verify that sufficient panel space and depth is available.
Note 3: Retrofit controller outputs are different. Add external interposing mechanical or solid state relay if applicable.
Note 4: Retrofit controller has a programmable, not fixed set point. Lock set point using controller's lockout parameter.
Note 5: For DIN rail mounting or sub-panel mounting, purchase DIN rail adapter p/n 0822-0586-P001 for 1/32 DIN or p/n 0822-0586-P002 for 1/16 DIN.
Note 6: Add a quencharc suppressor, Watlow p/n 0804-0147-0000, for inductive loads.
Note 7: Retrofit does not have equivalent action (as example, no manual reset)
Note 8: Retrofit controller does not have dual dial scale.
Note 9: Hardware lockout is not available on retrofit.
Note 10: Retrofit controller does not have user selectable line voltage.
Note 11: Retrofit does not support remote set point or retransmit. If wires are on these pins, select a different retrofit.
Note 12: Retrofit controller does not have user selectable control action.
Note 13: Solid state sensor required for humidity. See http://www.vaisala.com
Note 14: Retrofit controller does not have user selectable control mode.
Note 15: Use auxiliay event board A007-1732-F4B8
Note 16: Retrofit communications are different, consult specifications.
Note 17: Verify retrofit input range matches application.
Watlow Controls 3/30/2005 Page 106