Brocade FastIron SX, FCX, and ICX Diagnostic Reference - Manual (Page 119)

Brocade FastIron SX, FCX, and ICX Diagnostic Reference 107
53-1003076-02
IPv6 OSPF debug commands
5
This command displays debug information about NSM events as shown in the following example.
Brocade# debug ipv6 ospf nsm-events
OSPFv3: nsm-events debugging is on
Brocade(config-if-e1000-8/9)# Debug: Jan 1 20:04:10 OSPFv3: NSM[10.2.2.2, 644]:
HelloReceived at 733918, 1465981
Debug: Jan 1 20:04:10 OSPFv3: NSM[10.2.2.2, 644]: HelloReceived at 733918,
1465981
Debug: Jan 1 20:04:11 OSPFv3: NSM[644]: SendHello at 733932
Debug: Jan 1 20:04:19 OSPFv3: NSM[10.2.2.2, 644]: HelloReceived at 734019,
1466183
Debug: Jan 1 20:04:19 OSPFv3: NSM[10.2.2.2, 644]: HelloReceived at 734019,
1466183
Debug: Jan 1 20:04:20 OSPFv3: NSM[644]: SendHello at 734028
Debug: Jan 1 20:04:28 OSPFv3: NSM[10.2.2.2, 644]: HelloReceived at 734109,
1466363
Debug: Jan 1 20:04:28 OSPFv3: NSM[10.2.2.2, 644]: HelloReceived at 734109,
1466363
Debug: Jan 1 20:04:31 OSPFv3: NSM[644]: SendHello at 734133
debug ipv6 ospf nsm-status
Syntax: [no] debug ipv6 ospf nsm-status
This command displays information about the status of NSM as shown in the following example.
Brocade# debug ipv6 ospf nsm-status
OSPFv3: nsm-status debugging is on
Brocade(config-if-e1000-8/9)# Debug: Jan 1 20:06:44 OSPFv3: NSM[10.2.2.2]:
Status change [Down]->[Init](HelloReceived)
Debug: Jan 1 20:06:44 OSPFv3: NSM[10.2.2.2]: Status change [Init]->[2-way](No
Need Adjacency)
Debug: Jan 1 20:07:19 OSPFv3: NSM[10.2.2.2]: Status change
[2-way]->[ExStart](Need Adjacency)
Debug: Jan 1 20:07:24 OSPFv3: NSM[10.2.2.2]: Status change
[ExStart]->[ExChange](NegotiationDone)
Debug: Jan 1 20:07:24 OSPFv3: NSM[10.2.2.2]: Status change
[ExChange]->[Loading](Requestlist Not Empty)
Debug: Jan 1 20:07:24 OSPFv3: NSM[10.2.2.2]: Status change
[Loading]->[Full](LoadingDone)
debug ipv6 ospf packet
Syntax: [no] debug ipv6 ospf packet
This command displays all OSPFv3 packets in rx or tx mode as shown in the following example.
Brocade# debug ipv6 ospf packet
OSPFv3: packet debugging is on
Brocade(config-ospf6-router)# Debug: Jan 1 17:20:18 OSPFv3: Rcv Hello on ve 9
OSPFv3: (fe80::224:38ff:fed6:7800->OSPFv3: ff02::5)
RtrID:10.2.2.2 DR:10.4.4.8 BDR:10.2.2.2
Debug: Jan 1 17:20:18 OSPFv3: Rcv Hello on ve 9 OSPFv3:
(fe80::224:38ff:fed6:7800->OSPFv3: ff02::5)
RtrID:10.2.2.2 DR:10.4.4.8 BDR:10.2.2.2
Debug: Jan 1 17:20:23 OSPFv3: Snd Hello on ve 9 OSPFv3:
(fe80::224:38ff:fe21:6400->OSPFv3: ff02::5)
RtrID:10.4.4.8 DR:10.4.4.8 BDR:10.2.2.2
Debug: Jan 1 17:20:29 OSPFv3: Rcv Hello on ve 9 OSPFv3:
(fe80::224:38ff:fed6:7800->OSPFv3: ff02::5)
RtrID:10.2.2.2 DR:10.4.4.8 BDR:10.2.2.2