Brocade FastIron SX, FCX, and ICX Diagnostic Reference - Manual (Page 137)

Brocade FastIron SX, FCX, and ICX Diagnostic Reference 125
53-1003076-02
IPv6 PIM debug commands
5
SW forwarded pkt to 1 oif(s)
switch_to_spt: No. Thrshld: 1, Cnt: 108. RPT=0, Local-Rcvr=0
Rx Pkt (2001:DB8::200, ff0::14) on v1244(1/11).
* *: 0 pkt,from v1244(e1/11), dup. pkt to v55 phy e1/1, l2=0
SW forwarded pkt to 1 oif(s)
switch_to_spt: No. Thrshld: 1, Cnt: 162. RPT=0, Local-Rcvr=0
Rx Pkt (2001:DB8::200, ff0::15) on v1244(1/12).
* *: 0 pkt,from v1244(e1/12), dup. pkt to v55 phy e1/1, l2=0
SW forwarded pkt to 1 oif(s)
switch_to_spt: No. Thrshld: 1, Cnt: 162. RPT=0, Local-Rcvr=0
Rx Pkt (2001:DB8::200, ff0::16) on v1244(1/13).
* *: 0 pkt,from v1244(e1/13), dup. pkt to v55 phy e1/1, l2=0
SW forwarded pkt to 1 oif(s)
switch_to_spt: No. Thrshld: 1, Cnt: 161. RPT=0, Local-Rcvr=0
Rx Pkt (2001:DB8::200, ff0::17) on v1244(1/14).
* *: 0 pkt,from v1244(e1/14), dup. pkt to v55 phy e1/1, l2=0
SW forwarded pkt to 1 oif(s)
switch_to_spt: No. Thrshld: 1, Cnt: 161. RPT=0, Local-Rcvr=0
Rx Pkt (2001:DB8::200, ff0::14) on v1244(1/11).
* *: 0 pkt,from v1244(e1/11), dup. pkt to v55 phy e1/1, l2=0
SW forwarded pkt to 1 oif(s)
switch_to_spt: No. Thrshld: 1, Cnt: 163. RPT=0, Local-Rcvr=0
debug ipv6 pim regproc
Syntax: [no] debug ipv6 pim regproc
This command controls IPv6 PIM register processing and the command output resembles the
following example.
Brocade# debug ipv6 pim regproc
PIM6: regproc debugging is on
Brocade# PIMSM-REG.VRF0: (2001:DB8::200 ff0::1) Sending L2-Null Reg on iface v74
PIMSM-REG.VRF0: (2001:DB8::200 ff0::2) Sending L2-Null Reg on iface v74
PIMSM-REG.VRF0: (2001:DB8::200 ff0::3) Sending L2-Null Reg on iface v74
PIMSM-REG.VRF0: (2001:DB8::200 ff0::4) Sending L2-Null Reg on iface v74
PIMSM-REG.VRF0: (2001:DB8::200 ff0::5) Sending L2-Null Reg on iface v74
PIMSM-REG.VRF0: (2001:DB8::200 ff0::6) Sending L2-Null Reg on iface v74
PIMSM-REG.VRF0: (2001:DB8::200 ff0::7) Sending L2-Null Reg on iface v74
PIMSM-REG.VRF0: (2001:DB8::200 ff0::8) Sending L2-Null Reg on iface v74
PIMSM-REG.VRF0: (2001:DB8::200 ff0::9) Sending L2-Null Reg on iface v74
PIMSM-REG.VRF0: (2001:DB8::200 ff0::a) Sending L2-Null Reg on iface v74
PIMSM-REG.VRF0: (2001:DB8::200 ff0::b) Sending L2-Null Reg on iface v74
debug ipv6 pim rp
Syntax: [no] debug ipv6 pim rp
This command controls the Rendezvouz Point (RP) processing for IPv6 PIM events and the
command output resembles the following example.
Brocade# debug ipv6 pim rp
PIM6: rp debugging is on
Brocade# PIMv6-CRP.VRF0: Sending Candidate RP Msg (size 46)
PIMv6-CRP.VRF0: Sending Candidate RP Msg (size 46)