Brocade FastIron SX, FCX, and ICX Diagnostic Reference - Manual (Page 174)

162 Brocade FastIron SX, FCX, and ICX Diagnostic Reference
53-1003076-02
PIM debug commands
6
Join list: (10.10.129 225.1.1.2) wc=1 rpt=1 sparse=1
Join list: (10.11.10.101 225.1.1.2) wc=0 rpt=0 sparse=1
send_J/P_msg(), lcl_adr=10.10.119 dest=224.0.0.13 pkt_size=294 to v100
group address: 225.1.1.1
Join list: (10.10.129 225.1.1.1) wc=1 rpt=1 sparse=1
Join list: (10.11.10.101 225.1.1.1) wc=0 rpt=0 sparse=1
send_J/P_msg(), lcl_adr=10.10.119 dest=224.0.0.13 pkt_size=322 to v100
group address: 226.1.1.2
Join list: (10.10.129 226.1.1.2) wc=1 rpt=1 sparse=1
Join list: (10.11.10.101 226.1.1.2) wc=0 rpt=0 sparse=1
send_J/P_msg(), lcl_adr=10.10.119 dest=224.0.0.13 pkt_size=350 to v100
group address: 227.1.1.2
Join list: (10.10.129 227.1.1.2) wc=1 rpt=1 sparse=1
Join list: (10.11.99.99 227.1.1.2) wc=0 rpt=0 sparse=1
send_J/P_msg(), lcl_adr=10.10.119 dest=224.0.0.13 pkt_size=378 to v100
group address: 227.1.1.1
Join list: (10.10.129 227.1.1.1) wc=1 rpt=1 sparse=1
Join list: (10.11.99.99 227.1.1.1) wc=0 rpt=0 sparse=1
send_J/P_msg(), lcl_adr=10.10.119 dest=224.0.0.13 pkt_size=406 to v100
00:22:16 Send PIM_V2 Join/Prune Src 10.10.119 Dst 224.0.0.13 Len 406 on v100
PIMSM: END Periodic join-prune msgs
debug ip pim nbr-change
Syntax: [no] debug ip pim nbr-change nbr_address
The nbr_address variable specifies the IP address of the neighbor.
This command controls the PIM IPv4 neighbor changes and the command output resembles the
following example.
Brocade# debug ip pim nbr-change 10.144.144.12
PIM: nbr-change debugging is on
Brocade(config-if-e1000-1/1/11)# PIM-NBR.VRF0: Neighbor 10.144.144.12 on
interface tn4, 1/1/11 deleted on port-down
VRF0 Flow Entry Delete (10.0.0.168 232.0.0.11) HW bits: 0 0
VRF0 Flow Entry Delete (10.0.0.168 232.0.0.12) HW bits: 0 0
VRF0 Flow Entry Delete (10.0.0.168 232.0.0.13) HW bits: 0 0
VRF0 Flow Entry Delete (10.0.0.168 232.0.0.14) HW bits: 0 0
VRF0 Flow Entry Delete (10.0.0.168 232.0.0.15) HW bits: 0 0
VRF0 Flow Entry Delete (10.0.0.168 232.0.0.16) HW bits: 0 0
VRF0 Flow Entry Delete (10.0.0.168 232.0.0.17) HW bits: 0 0
VRF0 Flow Entry Delete (10.0.0.168 232.0.0.18) HW bits: 0 0
VRF0 Flow Entry Delete (10.0.0.168 232.0.0.19) HW bits: 0 0
VRF0 Flow Entry Delete (10.0.0.168 232.0.0.20) HW bits: 0 0
VRF0 Flow Entry Delete (10.0.0.168 232.0.0.21) HW bits: 0 0
VRF0 Flow Entry Delete (10.0.0.168 232.0.0.22) HW bits: 0 0
VRF0 Flow Entry Delete (10.0.0.168 232.0.0.23) HW bits: 0 0
VRF0 Flow Entry Delete (10.0.0.168 232.0.0.24) HW bits: 0 0
VRF0 Flow Entry Delete (10.0.0.168 232.0.0.25) HW bits: 0 0
VRF0 Flow Entry Delete (10.0.0.168 232.0.0.26) HW bits: 0 0
VRF0 Flow Entry Delete (10.0.0.168 232.0.0.27) HW bits: 0 0
VRF0 Flow Entry Delete (10.0.0.168 232.0.0.28) HW bits: 0 0
VRF0 Flow Entry Delete (10.0.0.168 232.0.0.29) HW bits: 0 0
VRF0 Flow Entry Delete (10.0.0.168 232.0.0.30) HW bits: 0 0
VRF0 Flow Entry Delete (10.0.0.168 232.0.0.31) HW bits: 0 0
VRF0 Flow Entry Delete (10.0.0.168 232.0.0.32) HW bits: 0 0
VRF0 Flow Entry Delete (10.0.0.168 232.0.0.33) HW bits: 0 0
VRF0 Flow Entry Delete (10.0.0.168 232.0.0.34) HW bits: 0 0
VRF0 Flow Entry Delete (10.0.0.168 232.0.0.35) HW bits: 0 0