Brocade FastIron SX, FCX, and ICX Diagnostic Reference - Manual (Page 74)

62 Brocade FastIron SX, FCX, and ICX Diagnostic Reference
53-1003076-02
GRE debug commands
4
DEBUG 0x8: Can not find route for tunnel id 11, hw index 23, src 10.22.33.254,
dest 10.22.33.252
DEBUG 0x8: create GRE tunnel origination because find route for tunnel id 11, hw
index 23, src 10.22.33.254, dest 10.22.33.252
DEBUG 0x8: Route for tunnel id 11 is via another tunnel or management port 22
DEBUG 0x8: Direct route for tunnel id 11 dest 10.22.33.252 has unresolved ARP
DEBUG 0x8: indirect route for tunnel id 11 dest 10.22.33.252 next hop 10.11.25.5
has unresolved ARP
DEBUG 0x8: indirect route for tunnel id 11 destination 10.22.33.252 next hop
10.11.25.5 has resolved ARP - CMD => route
DEBUG 0x8: Set next hop to Drop for tunnel id 11, hw index 23, src 10.22.33.254,
dest 10.22.33.252
DEBUG 0x8: Tunnel 11 - next hop 10.11.25.5 has no link-layer
DEBUG 0x8: bring tunnel id 11 up with drop
DEBUG 0x8: Create tunnel id 11 with next hop 185276677 - old next hop is 125276633
DEBUG 0x8: bring tunnel id 11 up
Update_hw_routes for Tunnel 11
Path MTU: Tunnel 11 - reset path mtu timer 456 (3344)
Path MTU: Tunnel 11 - failed to reset path mtu timer 456 (3344)
debug ip gre keepalive
Syntax: [no] debug ip gre keepalive
This command activates the Generic Routing Encapsulation (GRE) keepalive debugging.
Brocade# debug ip gre keepalive
GRE_MP: Keepalive Bring DOWN GRE Tunnel 11
GRE_MP: Keepalive Bring UP GRE on Tunnel 11 - port is 2/1/2
GRE_MP: RX Keepalive packet on tnnl 11 src 10.22.33.254, dst 10.22.33.252
GRE_MP: TX Keepalive packet on tnnl 11 we need to find outgoing port
GRE_MP: TX Keepalive packet on tnnl 11 - outgoing_port is 2/1/2 with mac
0000.00bb.ef40 vlan 2
GRE_MP_KEEPALIVE: NO FREE BUFFER AVAILABLE
GRE_MP: For Tunnel 11, Keepalive timeout after 3 seconds
GRE_MP: For Tunnel 11, stop keep-alive
GRE_MP: For Tunnel 11, start keep-alive
GRE_MP: enqueue Keepalive packet on tunnel 11 at index 23
GRE_MP: dequeue Keepalive packet on tunnel 11 at index 23
debug ip gre packet
Syntax: [no] debug ip gre packet
This command activates the debugging of GRE packet processing.
Brocade# debug ip gre packet
GRE: Error - IP GRE packet with invalid Ptype 0x1A4
GRE: Error - IP GRE packet with invalid first word 0x2C
GRE: Error - IP GRE packet with invalid first word 0x2C
GRE fragment : Rx IP GRE Pkt: src 10.22.33.254, dst 224.0.0.5, len 64 id 324
GRE Packet too big - need extra processing: Rx IP GRE Pkt: src 10.22.33.254, dst
224.0.0.5, len 64
GRE Reassembly: Rx IP GRE Pkt: src 10.22.33.254, dst 224.0.0.5, len 64
GRE : Rx IP GRE Pkt: src 10.22.33.254, dst 224.0.0.5, len 64
GRE: Error - Rx IP Pkt with invalid Inner IPv4 header
GRE: Error - Rx IP Pkt with 2 GRE headers: Inner src 10.22.33.254, Inner dst
224.0.0.5, len 64
GRE: Dropping the packet as GRE tnnl 11 is not UP
GRE_LP: Error - LP TX GRE packet is in LOOP