Hardy HI 2151/30WC Single-Scale Controller - Manual (Page 6)

List of Tables
a
LIST OF TABLES
CHAPTER 2 - INSTALLATION - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 2-1
TABLE 2-1 CABLE TERMINATION REQUIREMENTS - - - - - - - - - - - - - - - - - - - - - - - - 2-1
CHAPTER 3 - SETUP - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 3-1
TABLE 3-1 INTERIOR DIP SWITCHES - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 3-3
TABLE 3-2 EXTERIOR DIP SWITCHES - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 3-4
TABLE 3-3 BINARY QUARTER NUMBER - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 3-4
CHAPTER 4 - DISCRETE TRANSFERS - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 4-1
TABLE 4-1 DISCRETE WRITE - 2 WORDS (16 BITS EACH) - - - - - - - - - - - - - - - - - - - - - 4-1
TABLE 4-2 DISCRETE READ - 2 WORDS (16 BITS EACH) - - - - - - - - - - - - - - - - - - - - - 4-2
CHAPTER 5 - BLOCK TRANSFERS - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 5-1
TABLE 5-1 FOUR BYTE NUMERIC FORMAT FOR WEIGHT PARAMETERS - - - - - - - - - - - - - 5-1
TABLE 5-2 BLOCK READ COMMAND NUMBER 1: FULL STATUS AND WEIGHT DATA - - - - - - - 5-2
TABLE 5-3 BLOCK READ COMMAND NUMBER 2: SETPOINT RELAY PARAMETERS - - - - - - - 5-5
TABLE 5-4 SETPOINT DESCRIPTION BYTES - - - - - - - - - - - - - - - - - - - - - - - - - - - - 5-5
TABLE 5-5 SETPOIINT DESCRIPTION BYTES - - - - - - - - - - - - - - - - - - - - - - - - - - - 5-5
TABLE 5-6 BLOCK READ COMMAND NUMBER 3: INSTRUMENT
IDENTIFICATION AND DIAGNOSTICS - - - - - - - - - - - - - - - - - - - - - - - - 5-6
8ABLE 5-7 BLOCK READ COMMAND NUMBER 4: READ TARE VALUE - - - - - - - - - - - - - - - 5-7
TABLE 5-8 BLOCK READ COMMAND NUMBER 5: CALIBRATION PARAMETERS - - - - - - - - - - 5-8
TABLE 5-8 BLOCK READ COMMAND NUMBER 6: CONFIGURATION OF RATE-OF-CHANGE - - - 5-8
TABLE 5-10 BLOCK READ COMMAND NUMBER 7: BCD OUTPUT CONFIGURATION - - - - - - - - 5-9
TABLE 5-11 BLOCK READ COMMAND NUMBER 8: CONFIGURATION OF ANALOG OUTPUT - - - - 5-10
TABLE 5-12 BLOCK READ COMMAND NUMBER 9: CONFIGURATION OF STANDARD RS232 PORT 5-11
TABLE 5-13 BLOCK READ COMMAND NUMBER 10: STICKER VALUE - - - - - - - - - - - - - - - - 5-11
TABLE 5-14 BLOCK READ COMMAND NUMBER 11: AUTO ZERO TOLERANCE - - - - - - - - - - - 5-12
TABLE 5-15 BLOCK READ COMMAND NUMBER 12: INTEGRATED TECHNICIAN - - - - - - - - - - 5-13
TABLE 5-16 BLOCK WRITE COMMAND NUMBER 51: ACTIVATE SCALE FUNCTIONS - - - - - - - - 5-15
TABLE 5-17 BLOCK WRITE COMMAND NUMBER 52: DOWNLOADING
SETPOINT RELAY PARAMETERS - - - - - - - - - - - - - - - - - - - - - - - - - - 5-17
TABLE 5-18 SETPOINT DESCRIPTION BYTES - - - - - - - - - - - - - - - - - - - - - - - - - - - - 5-17
TABLE 5-19 SETPOIINT DESCRIPTION BYTES - - - - - - - - - - - - - - - - - - - - - - - - - - - 5-17
TABLE 5-20 BLOCK WRITE COMMAND NUMBER 53: SEND TARE VALUE - - - - - - - - - - - - - - 5-18
TABLE 5-21 BLOCK WRITE COMMAND NUMBER 54: SCALE CALIBRATION ACTION - - - - - - - - 5-19
TABLE 5-22 BLOCK WRITE COMMAND NUMBER 55: CALIBRATION PARAMETERS - - - - - - - - 5-20
TABLE 5-23 BLOCK WRITE COMMAND NUMBER 56: CONFIGURATION OF RATE-OF-CHANGE - - 5-21
TABLE 5-24 BLOC WRITE COMMAND NUMBER 57: BCD OUTPUT CONFIGURATION - - - - - - - - 5-22
TABLE 5-25 BLOCK WRITE COMMAND NUMBER 58: CONFIGURATION OF ANALOG OUTPUT - - 5-23
TABLE 5-26 BLOCK WRITE COMMAND NUMBER 59: CONFIGURATION OF
STANDARD RS232 PORT - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 5-24
TABLE 5-27 BLOCK WRITE COMMAND NUMBER 60: STICKER VALUE - - - - - - - - - - - - - - - 5-24
TABLE 5-28 BLOCK WRITE COMMAND NUMBER 61: AUTO ZERO TOLERANCE - - - - - - - - - - 5-25
TABLE 5-29 BLOCK WRITE COMMAND 62: WAVERSAVER/EXCITATION MONITOR - - - - - - - - - 5-25
TABLE 5-30 BLOCK READ COMMAND NUMBER 70: READING RESPONSE
CODE AFTER A BLOCK WRITE - - - - - - - - - - - - - - - - - - - - - - - - - - - - 5-30
CHAPTER 6 - CONVERSION CHARTS AND FORMULAS 6-1
TABLE 6-1 HEX CHART - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 6-1