Montigo H36PVN - Manual (Page 4)

H36PVN Power Vent Indoor Gas Fireplace
Page 4
XG0649 - 031511
Installation
Section: Section A: Before You Begin
Installation and repairs should be done by an
authorized gas fireplace service technician. The
appliance should be inspected before use and at
least annually by a professional. More frequesnt
cleaning may be required due to exessive lint from
carpeting, bedding material, ect. It is imperative
that control compartments, burners and circulating
air passageways of the fireplace are kept clean.
NOTICE
XW2016
Important Message
Save these Instructions
The H36PV Power Vent fireplaces must be installed in
accordance with these Instructions . Carefully read all the
Instructions in this manual first . Consult the Local Gas Branch to
determine the need for a permit prior to starting the installation .
It is the responsibility of the installer to ensure this fireplace is
installed in compliance with the manufacturers instructions and
all applicable codes .
BEFORE YOU START:
Pre-Installation Checklist
■ Determine the desired install location of your fireplace .
■ See Section 1, Dimensions on Page 5, and refer to the
Framing Section 2 for details .
■ Select your type and location of your Power Vent
run: Roof Mounted (EDVRSPV58) or Wall Mounted
(EDVWSPV58) .
■ Your termination location should be selected to provide
the shortest possible vent run .
■ Lay out the Vent run; calculating the required elbows
and straight runs of 5"/8" flex or rigid pipe .
■ Refer to the Section 4 on Page 10, "Installing the Power
Vent" for details .
■ Montigo supplies 20' of low voltage wire, which can be
spliced to any length . This wire CANNOT run in conduit
with any other wire .
■ Refer to Section 5 on Page 18, for Wiring Details .
■ The gas connection is located on the bottom side of the
fireplace .
■ Refer to local codes and guidelines for installation
requirements .
■ Installation and repairs should be done by a qualified
contractor and must conform to:
• Installations in Canada must conform to the current
CAN/CGA B-149 .1 and .2 Gas Installation Code and
local regulations .
• Installations in the USA must conform to local
codes, or in the absence of local codes to the National
Fuel Gas Code, ANSI Z223 .1-1988 .
• See Appendix C for installation within the State
of Massachusetts. This fireplace must comply with
NFPA-54 Chapter 10 .
■ Refer to Section 6 Page 21, "Installing the Gas Line" for
Details .
Understanding the Basic Operation
Residential H36PV fireplace
To operate the fireplace, Montigo has supplied and installed
twenty feet of low voltage wire to this electrical control panel .
Connect the two wire harness to a standard single pole ON/
Off switch located at a location of your choice . You may also
extent these wires to any length, as long as you select a wire
of equal quality .
XW2018
Due to high operating temperatures, this appliance
should be located out of traffic & away from
furniture and draperies.
Children and adults should be alerted to the
hazards of the high surface temperature, which
could cause burns or clothing ignition.
Young children should be carefully supervised
when they are in the same room as the appliance.
Clothing or other flammable materials should not
be placed on or near the appliance.
CAUTION
Irritant Cutting Watch your step Slippery floor High temperatures Glass hazard Danger of suffocation
High voltage Toxic Flammable materials Corrosive Fork lift trucks Danger overhead crane Explosion risk
Oxidising Danger of death Biohazard Laser Radiation Danger of entrapment Hot surface General Warning
Blank
Gas bottles Watch for falling objects Electricity Danger for cutter Entrapment hazard Battery hazard Rotating parts
Low temperature Strong magnetic field Optical radiation Non ionizing radiation Radiation Hazardous to the Environment Danger of harming your hands
Irritant Cutting Watch your step Slippery floor High temperatures Glass hazard Danger of suffocation
High voltage Toxic Flammable materials Corrosive Fork lift trucks Danger overhead crane Explosion risk
Oxidising Danger of death Biohazard Laser Radiation Danger of entrapment Hot surface General Warning
Blank
Gas bottles Watch for falling objects Electricity Danger for cutter Entrapment hazard Battery hazard Rotating parts
Low temperature Strong magnetic field Optical radiation Non ionizing radiation Radiation Hazardous to the Environment Danger of harming your hands
Irritant Cutting Watch your step Slippery floor High temperatures Glass hazard Danger of suffocation
High voltage Toxic Flammable materials Corrosive Fork lift trucks Danger overhead crane Explosion risk
Oxidising Danger of death Biohazard Laser Radiation Danger of entrapment Hot surface General Warning
Blank
Gas bottles Watch for Electricity Danger for cutter Entrapment hazard Battery hazard Rotating parts
When this appliance is installed directly
on any combustible material other than
wood flooring, it must be installed on a
metal or wood panel extending the full
width and depth of the appliance or a
fire will occur causing serious injury,
property damage or even death.
XW2020
DANGER
XW2020-When-Installed_[EN].pdf 1 1/24/2011 12:48:53 PM