REMKO KWL 130 H - Manual (Page 13)

Operating structure
> 5 sec.
< 2 sec.
< 2 sec. > 5 sec. < 2 sec.
< 2 sec.
< 2 sec.
< 2 sec.
> 5 sec.
+
+
/
/
Open configuration
Value/parameter up
Open submenu/value
Close configuration
Value/parameter down
Close submenu
+
+
Standard display
Change target values
C/H target value change
Value change in cooling
between 10.0 and 18.0 and in
heating between 36.0 and 43.0
with the key /, save with
"SET".
Param.level 2 with password
All parameters
Input
Password
All parameters of
the Submenus:
St, CF, Sd, ES, CO,
Ar, dF
Display target values
Display target value cooling
Current target value in cooling mode
Display target value heating
Current target value in heating mode
Menu without password
Current fault list
currently pending, non-
resettable faults are displayed
with "no", resettable faults are
displayed with "rSt"; resetting
with the SET key.
Operating hours compressor 1
Value in hours, resettable after
maintenance, etc. by pressing the
SET key (5 sec.).
Parameter backup to
hotkey
Using a plugged-in hotkey
the current parameters of the
controller can be transferred to
the hotkey.
Operating hours compressor 2
Value in hours, resettable after
maintenance, etc. by pressing the
SET key (5 sec.).
Reset fault list
Faults are displayed in the
sequence n01 (oldest) to n50
(most recent). Through input of
the password under "ArSt" the
list can be reset.
Pump operating hours
Value in hours, resettable after
maintenance, etc. by pressing
the SET key (5 sec.).
Defrosting period
Value in min. and sec. until the
next defrosting interval
Param.level 1 without password
St 01 Target value cooling
St 02 Hysteresis cooling
St 03 Target value heating
St 04 Hysteresis heating
St 09 Output range
Pr2 Password
CF 16 ID 5 Configuration
CF 24 Pb 1 Shut-off
CF 25 Pb 2 Shut-off
CF 26 Pb 3 Shut-off
CF 27 Pb 4 Shut-off
CF 28 Unit active/operating mode
CF 29 Autom. changeover target value
CF 30 Hysteresis changeover
CF 31 Cooling / heating display icon
CF 32 °C/°F conversion
CF 37 Company version
Pr2 Password
Sd 01 Dyn. target value configuration
Sd 02 Shut-off dyn. target value C
Sd 03 Shut-off dyn. target value H
Sd 04 Outside temp. sensor target value C
Sd 05 Outside temp. sensor target value H
Sd 06 Outside temp. sensor hysteresis C
Sd 07 Outside temp. sensor Hysteresis H
Pr2 Password
ES 01 Switch-on time
ES 02 Shut-off time
ES 03 Activation Monday
ES 04 Activation Tuesday
ES 05 Activation Wednesday
ES 06 Activation Thursday
ES 07 Activation Friday
ES 08 Activation Saturday
ES 09 Activation Sunday
ES 10 Target value cooling
ES 11 Hysteresis cooling
ES 12 Target value heating
ES 13 Hysteresis heating
Pr2 Password
Ar 03 Target value anti-freeze protection fault C
Ar 04 Hysteresis anti-freeze protection fault C
Ar 08 Target value anti-freeze protection heating C
Ar 09 Target value anti-freeze protection heating H
Ar 10 Target value cooling W/W
Ar 11 Hysteresis cooling W/W
Ar 12 Hysteresis heating W/W
Ar 13 Config. anti-freeze protection heating
Ar 14 Config. Cooling
Ar 20 E-heating active/operating mode
Ar 21 Target value air temp. active
Ar 22 Hysteresis air temp. active htg
Ar 24 After-run time E-heating 2
Ar 25 Target value air temp. active compr.
Ar 26 Target value air temp. locked compr.
Ar 27 Target value anti-freeze protection fault H
Ar 28 Hysteresis anti-freeze protection fault H
Ar 29 Target value external pump W/W
Ar 30 Hysteresis external pump W/W
Ar 31 Pump active/operating mode
Ar 32 Pump active/operating mode
Pr2 Password
dF 02 Defrosting input parameter
dF 03 Target value defrosting start
dF 04 Target value defrosting end
dF 05 Min. operating time before
defrosting start
dF 06 Minimum defrosting time
dF 07 Maximum defrosting time
dF 10 Min.time defrosting interval
dF 11 Target value defrosting begin (df 10)
dF 12 Target value defrosting (dF 10)
dF 16 Active fault low temperature
dF 19 Target value forced defrost. begin
dF 20 Hysteresis forced defrost. begin
Pr2 Password
Pr2 Password
Pr2 Password
Pr2 Password
All open
parameters
Target values
Configuration
Dyn. target value
Energy-saving
cycle
Compressor
Fan
Anti-freeze
protection
Faults
Defrost
Display adaptive target value
Current, adaptive target value
Display of current values
Medium outlet display
Current value (supply)
Medium intake display
Current value (return)
Condenser display
Current value of condenser tem-
perature or pressure (with winter
pressure controller accessory)
13